manualshive.com logo in svg

Sentec SDM, Service Manual

Share
Download
Sentec SDM Service Manual Download Page 22

3 Maintenance/Safety & Functionality Tests 

 

 

HB-005615-j 

16 

3.1.6

 

Sensor Temperature Surveillance 

Note: The ‘Sensor Temperature’ Icon in the Status Bar indicates the measured sensor 

temperature (in °C). 

Connect  the  sensor  to  the  SDM  and  switch  on  the  monitor.  Verify  that  the  sensor 
temperature reaches the SET temperature within 2 to 3 minutes. Then immerse the 

sensor  into  clean  tap  water  of  45°C  -  50°C  and  verify  that  the  measured  sensor 
temperature  increases  (i.e.  by  observing  the  temperature  indicator  located  in  the 
Status Bar of the SDM`s display). Verify that the red sensor LED switches off, a low 

priority alarm starts to sound and that the message "Temp. limiter active" (or ‘Sensor 
problem 38’, ‘Sensor problem 42’) displays. 
If the message “Sensor Fault xx” was triggered you must restart the SDM to reset the 
message. Do not use the sensor if the message “Sensor Fault xx” is not reset by power 

cycling  the  SDM.  Instead  contact  qualified  service  personnel  or  your  local  SenTec 
representative. 
Do not use the sensor if the test fails! 

CAUTION:  Ensure  that  the  temperature  of  the  water  bath  is 
< 50°C. Temperatures above 50°C may damage the sensor. 

 

 

 

3.1.7

 

Cleaning / Inspecting without Membrane 

1.

 

Remove  the  sensor  membrane  using  the  membrane  remover  located  at  the 
bottom of the Membrane Changer as shown in the figure below (note that the 
Membrane Changer is shown upside down). Step 

: Slide the SenTec TC Sensor 

into  the  membrane  remover  with  its  membrane  facing  the  bottom  of  the 
Membrane  Changer.  Step 

:  Lift  the  SenTec  TC  Sensor  up  to  remove  the 

membrane from the sensor body. 

 

 

 

Figure 3 

Removal of the Membrane from the TC Sensor 

 

CAUTION:  Do  not  touch  any  of  the  measuring  units  in  the 
center  of  the  sensor  surface  after  removing  the  sensor 
membrane. Do not rub the sensor surface. 

 

 

 

Summary of Contents for SDM






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands