manualshive.com logo in svg

Sentec SDM, Service Manual

Share
Download
Sentec SDM Service Manual Download Page 20

3 Maintenance/Safety & Functionality Tests 

 

 

HB-005615-j 

14 

3

 

Maintenance/Safety & 

Functionality Tests  

 
At normal use there is no internal adjustment or new calibration of the SDM required. 
However,  to  guarantee  continuous  performance,  reliability  and  safety  of  the  SDMS 

routine checks and maintenance procedures (including cleaning/disinfection) as well 
as safety checks should be performed regularly. 
Routine checks and maintenance procedures that can be performed by the 

operator 

are provided in the 

Instruction Manual for the SDMS. Instructions for cleaning and/or 

disinfecting the SenTec Digital Monitor (SDM) and the ‘Digital Sensor Adapter Cable’, 
are  provided  in  the 

Technical  Manual  for  the  SDM.  Please  refer  to  the  respective 

Directions  for  Use  for  instructions  for  cleaning  and/or  disinfection  of  SenTec  TC 

Sensors.  For  a  better  overview  and  documentation  of  periodic  routine  checks  and 
maintenance to be performed by the operator the SenTec form 

HB-007601 “SDMS 

Maintenance Checklist”  (see section 

8.7

) is available (refer to the Manual CD). 

It is recommended that 

qualified service personnel 

performs the maintenance and 

a complete safety and functionality test as specified in this Manual at regular intervals 
(recommended every 12 month but at least every 24 months). Use the 

HB-005638 

“Protocol for Safety & Functionality Test” (see section 

8.1

 "Protocol for Safety & 

Functionality Test") to guide you through the complete "Safety & Functionality Test" 

and  to  document  your  test  results.  To  perform  a  complete  "Safety  & 
Functionality Test" all tests described in this chapter MUST be performed. 
 
 
Note:  Prior to maintenance, service or repairs all components of the SDMS must be 

cleaned  and  disinfected.  If  equipment  is  send  to  service  personnel,  a  local 

SenTec  representative  or  to  SenTec  AG  a  completed 

“Certificate  for 

Disinfection” (see section 

8.7

) must be attached. 

 
 

WARNING:  If  any  of  the  tests  specified  below  fails,  the 

respective  problem  must  be  fixed  before  the  equipment  is 
returned to the user. 

 

 

 

 

Summary of Contents for SDM






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands