manualshive.com logo in svg

Sensotec Rapidox 1100ZR-H-OL-LC, Instruction Manual, Page: 27 / 55

Share
Download
Sensotec Rapidox 1100ZR-H-OL-LC Instruction Manual Download Page 27

D11-044-1:  Rapidox 1100ZR-H-OL-LC O

2

 Analyser Instruction Manual 

 

 

D11-044-1 

21 

Last printed 08/11/2016 12:10:00 

 
 

 

6

 

Rapidox Software Instructions 

 

Please refer to the Appendix for Heller specific software features.

 

 

6.1

 

Software Installation 

 

It is possible to programme a range of variables to the Rapidox using an RS232 (or 
RS485 if configured) link with a PC running MS-Windows (all versions) and the 
supplied Rapidox software.  The software is supplied on a memory stick which 
contains a setup.exe file to install. 
 

The software has been tested successfully on most language machines including 
Chinese, Korean & Japanese and all current versions of Windows operating 
system.  We do not recommend the use of Vista as connecting devices to this 
operating system can be problematical at best. 
 

Note that software is ‘regionally aware’ and will therefore accept and display data 
using the decimal separator that is set in the PC’s Regional Settings in the Control 
Panel.  For example, in the UK or US, you might enter the value 2.5 - in 
continental Europe this would normally be entered as 2,5 assuming the PC’s 
Regional Settings have been set up to use ‘,’ as the decimal separator. 

 

6.2

 

Getting Started 

 

Make sure that the Rapidox is connected to a free serial port on the rear of your 
computer.  These will nearly always be COM1 or COM2 but the software will scan 
through the ports until it finds the Rapidox.  The analyser must be switched on for 
this to succeed and while you are communicating with it.  If you are using a serial 
USB cable please make sure the chipset it manufactured by FTDI as other brands 

have prven to be unreliable.  On start up the software will locate the Rapidox and 
display the following page: 

 

 

 

Summary of Contents for Rapidox 1100ZR-H-OL-LC
























































Reviews:

No comments