SENSIT Technologies SMART-CAL 360 Instruction Manual Download

Page: 15 / 20

SUPERVISOR MENU

The supervisor menu has options that may need to be changed or adjusted in the field. To access the supervisor

menu, select the menu button

in the bottom right of the main display. Enter the supervisor password. “Supervisor

Menu” should appear at the top of the display.

NOTE

: This menu is password protected. If you do not have the password and need to access this menu,

contact SENSIT Technologies for assistance.

ATE

IME

Adjustment for date and time of the station. The

date and time are used to timestamp records and

update the date and time of any instrument

connected to the station.

IME

ONE

Adjustment for the time zone of the station.

ETWORK

ETTINGS

Network setup for LAN/WAN, IP address, gateway,

etc. Only available for stations configured as

SCAL-N.

ACKUP

ESTORE

Allows user to take manual backups of the

database and restore the database using a backup.

Normally backups are done automatically (if the
“Auto Backup” option is enabled) and does not
need to be done manually.

ALVE

ONFIGURATION

Setup for how gas cylinders are attached to the

manifold on the back of the station.

ESET

ALVE

ONFIGURATION

Resets the valve configuration to the default setup.

YLINDER

RACKING

Enable or disable cylinder tracking feature. This

allows the user to enter details about each gas

cylinder attached to the station such as expiration

date and lot numbers. This information can then be

retrieved by SCAL 360 Data Management software

to send alerts related to gas usage.

RASE

UMP

OGS

Password protected option that permanently erases

all records.

Contact SENSIT Technologies before

using this option.

ESET

ETTING

Password protected option that resets all settings in

the station to default values.

ALIBRATE

RESSURE

ENSOR

Calibration procedure for the internal pressure

sensor of the station. Generally, this is only done

once at the factory and does not need to be reset.

ANGUAGE

Change display language used in the user interface

of the station. Currently supported languages are

English and Turkish.

ACKLIGHT

Adjustment for brightness of the display backlight.

TLS

1.2

UPPORT

Option to enable or disable TLS 1.2 security

support (applies to SCAL-N only)

YSTEM

EBOOT

Reboots the station.

HUT

OWN

Shuts down power to the station. This is the

preferred method to power the station off, rather

than unplugging it.

BOUT

YSTEM

Displays the system and application software

revisions numbers as well as license information.

Summary of Contents for SMART-CAL 360





















Search results

Summary of Contents for SMART-CAL 360

Reviews:

Related manuals for SMART-CAL 360

Brands by name

Popular brands

SENSIT Technologies SMART-CAL 360, Instruction Manual

Search results

Summary of Contents for SMART-CAL 360

Reviews:

Related manuals for SMART-CAL 360

Brands by name

Popular brands