manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

The senseFly EBEE RTK Extended User Manual is a comprehensive guide that provides in-depth instructions for operating and optimizing your EBEE RTK drone. Designed for easy access and understanding, this manual is available for free download from our website, allowing you to make the most of your product's capabilities.

Share
Download
background image

Quick start guide

4.3 The setup phase of a flight

The setup phase of a flight includes the waypoints and actions related to the take-
off and landing of the

eBee RTK

and includes the following locations:

•

Take-off location:

The point from which the drone is launched, automati-

cally set to the location calculated from GPS/GLONASS signals by the drone
when it is launched. This location defines the altitude of 0 m/ATO (ATO
stands for above take-off); the altitudes of all other waypoints, when de-
fined in m/ATO, are referenced to the altitude of this location.

•

Start waypoint:

The first point that the drone flies towards when launched

(once it reaches the take-off transition altitude).

•

Home waypoint:

The safe point for the drone to circle in case of emer-

gency, as well as its landing position at the end of a flight for both Linear
and Circular landings.

wind
direction

obstacle-
free zones

40m

take-off 

transition

altitude reached

10m

60m

Take-off 

location

Home

waypoint

Start

waypoint

Approach

sector

50

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Related manuals for EBEE RTK

Lamsam DF805B Operation Manual preview
DF805B
Brand: Lamsam Pages: 15
Potensic Dreamer Mini User Manual preview
Dreamer Mini
Brand: Potensic Pages: 12
Trident OpenROV Operation Manual preview
OpenROV
Brand: Trident Pages: 44
Tundra Drone Siren Herder Quick Start Manual preview
Siren Herder
Brand: Tundra Drone Pages: 23
NX NX-8100F User Manual preview
NX-8100F
Brand: NX Pages: 24
NX NX-HD16100W User Manual preview
NX-HD16100W
Brand: NX Pages: 28
sky rider HAWK 2 DR187 User Manual preview
HAWK 2 DR187
Brand: sky rider Pages: 18
Origaudio FLYINGTON User Manual preview
FLYINGTON
Brand: Origaudio Pages: 2
Estes protoZ Instructions preview
protoZ
Brand: Estes Pages: 2
Valore BLUEJAY LA17 User Manual preview
BLUEJAY LA17
Brand: Valore Pages: 6
Foamdrones Baby Turtle Building Instructions preview
Baby Turtle
Brand: Foamdrones Pages: 13
Propel Trampolines SKY FORCE Instruction Booklet preview
SKY FORCE
Brand: Propel Trampolines Pages: 2
Propel RC SKYWRITER UFO User Manual preview
SKYWRITER UFO
Brand: Propel RC Pages: 2
Propel Trampolines PROTON MICRO DRONE Instruction Booklet preview
PROTON MICRO DRONE
Brand: Propel Trampolines Pages: 6
Propel RC ZIPP NANO 2.0 Instruction Booklet preview
ZIPP NANO 2.0
Brand: Propel RC Pages: 6
Propel RC DART 1.0 Instruction Booklet preview
DART 1.0
Brand: Propel RC Pages: 7
Propel RC HD SONIC DRONE Instruction Booklet preview
HD SONIC DRONE
Brand: Propel RC Pages: 8
Mi YKFJ01FM User Manual preview
YKFJ01FM
Brand: Mi Pages: 73

Brands by name

Popular brands

Load more brands