background image

Specifications

RPAS

Remotely Piloted Aircraft System

A term used for drones or UAVs, the software and technology they use to
navigate.

RTCM

Radio Technical Commission for Maritime Services

An international organisation that standardises transmission protocols that
allow for RTK positioning, for example, RTCM 2.x and RTCM 3.x. They also
publish the Ntrip standard.

RTK

Real Time Kinematics

A technique used to enhance the accuracy of coordinates calculated from
GNSS signals.

triangle model

An approximate representation of a surface, constructed from

connected triangles.

UAS

Unmanned Aircraft System

A term used for drones or RPASs, the software and technology they use to
navigate.

UAV

Unmanned Aerial Vehicle

Another term for drone.

VRS

Virtual Reference Station

A reference station that does not exist on the ground, but instead is created
by combining correction data (delivered over Ntrip) from several real refer-
ence stations. VRS RTK corrections relative to this virtual reference station
can then be made as if it were a real reference station.

190

Summary of Contents for EBEE RTK































































































































































































Reviews: