manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 142

Advanced functionalities

8.2 Pre-flight testing of the remote control

If you plan to use the remote control during a flight we recommend that you first
test it on the ground. Ensure that the

eBee RTK

is set to Full Manual mode⁴⁷ and

follow these steps:

1. Check that the left stick on the remote control is in the low position to pre-

vent the propeller from spinning.

2. Turn on the remote control.

3. Turn on the

eBee RTK

by connecting the battery. Once the drone detects the

signal from the remote control it will change to one of the manual modes.

Caution:

The motor of the

eBee RTK

is now controlled by the remote

control and will begin spinning if the left stick is pushed up. Always
keep the area around the propeller clear of obstacles and body parts
to prevent injury.

4. Move the right stick on the remote control to verify proper reception by the

drone and correct servo direction.

5. Turn off the remote control for take-off.

Note:

If the remote control is switched on while it is performing pre-

flight checks the ailerons will not move when the checks are com-
pleted and the GPS/GLONASS signals are acquired.

For more information on using the remote control, refer to the original user man-
ual, available from the Knowledge Base within my.senseFly⁴⁸.

⁴⁷ see section ‘Enabling manual control’ on page 140
⁴⁸ http://my.sensefly.com

142

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands