manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

The senseFly EBEE RTK Extended User Manual is a comprehensive guide that provides in-depth instructions for operating and optimizing your EBEE RTK drone. Designed for easy access and understanding, this manual is available for free download from our website, allowing you to make the most of your product's capabilities.

Share
Download
background image

eMotion

in-depth guide

7.8 Camera tab

Photo sequence
control

Camera control

Camera parameters

for mapping

Camera model

Photo targets

New photo
target increment

Individual photos

The camera tab is an advanced tab that can be used to precisely control the func-
tioning of the camera. It also contains controls for taking oblique imagery. It is
split into several sections: ‘Camera model’, ‘Photo targets’, ‘Camera control’, and
‘Camera parameters for mapping’.

131

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Related manuals for EBEE RTK

Skydroid Yunzhuo MX450 UAV User Manual preview
Yunzhuo MX450 UAV
Brand: Skydroid Pages: 4
Fast Lane NEBULA CRUISER Manual preview
NEBULA CRUISER
Brand: Fast Lane Pages: 5
ProFlight PFBD101 User Manual preview
PFBD101
Brand: ProFlight Pages: 13
ProFlight ORBIT PFBD201 User Manual preview
ORBIT PFBD201
Brand: ProFlight Pages: 20
Alpha SPY DRONE Instruction Manual preview
SPY DRONE
Brand: Alpha Pages: 14
sky viper NANO DRONE Flying Manual preview
NANO DRONE
Brand: sky viper Pages: 4
TRNDlabs SWIFT User Manual preview
SWIFT
Brand: TRNDlabs Pages: 29
sky rider DR1717 v1772-01 User Manual preview
DR1717 v1772-01
Brand: sky rider Pages: 20
dji Matrice 600 Pro Quick Start Manual preview
Matrice 600 Pro
Brand: dji Pages: 8
Amax Voyage Aeronautics VA-1000 Instruction Booklet preview
Voyage Aeronautics VA-1000
Brand: Amax Pages: 9
YUNEEC Q500 Typhoon Instruction Manual preview
Q500 Typhoon
Brand: YUNEEC Pages: 58
Aircraft XAircraft X450 Instruction Manual preview
XAircraft X450
Brand: Aircraft Pages: 22

Brands by name

Popular brands

Load more brands