manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 129

eMotion

in-depth guide

7.7 Mission Waypoints tab

Selected mission

waypoint

parameters

Remaining

mission

waypoints

Add or reset

waypoints

The Mission Waypoints tab contains a list of all mission waypoints currently on
the drone autopilot. It can be used for finer control of individual waypoints in the
current mission. The list of waypoints displays the ID, Change altitude parameter,
Altitude and Action related to each mission waypoint.

Clicking on a mission waypoint in the list or in the Map Area will expand the panel
to display all the parameters related to that waypoint. These parameters are ex-
plained in detail in section ‘Waypoints and their properties’ on page 72. Changes
made to the selected waypoint are sent to the drone immediately after selecting
an item in the popup menu or upon hitting the ‘Enter’ key in the text fields. You
can reposition the waypoint by clicking the

button and then clicking at the de-

sired position in the Map Area. You can make the selected waypoint the current
waypoint by clicking the

button.

129

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands