background image

13

WWW.SENIXTOOLS.COM

•  Stand in the operating position Stand up straight. Do 

not bend over.

•  Keep feet apart and firmly planted.

•  Hold the shaft grip with the right hand. Keep the right 

arm slightly bent.

•  Hold the handle with the left hand. Keep the left arm 

straight.

•  Hold the unit at waist level.

•  Position the cutting head a few inches above the 

ground.

•  Do not over-reach; Keep all parts of your body away 

from the rotating cutting attachment and hot surfaces.

STARTING AND STOPPING

Restart a warm engine:

HOLDING THE UNIT

STOP THE ENGINE:

To start a cold engine:

1. Slowly press the primer bulb 5-10 times.

NOTE:

 After the 7th press, fuel should be visible in the 

primer bulb. If it is not, continue to press the primer until 

you see fuel in the bulb.
2. Push the choke button in to set the choke to FULL 

CHOKE position.

NOTE: 

Do not squeeze the throttle trigger because the 

choke will be pop out automatically.
3. Pull the starter grip /cord until resistance is detected. 

Rapidly pull 3 to 5 times or until you hear engine turn 

over or begin to start.

4. If engine does not start, release choke by squeezing 

throttle trigger and choke button pops out.

   a.Engine is now in the run position.

   b.Rapidly pull starter grip/cord until engine starts.

5. Allow the engine to run for 10 seconds,then squeeze 

throttle to provide fuel to engine and use for intended 

task.

NOTE:

 The choke button is only used when starting 

a cold engine. Never push the choke button in once 

the engine has been turned over or run. Otherwise the 

engine could be damaged.

NOTE:

 DO NOT push choke button in.

1. Make sure the primer bulb has fuel inside.

2. Rapidly pull starter/grip until engine starts.

3. Squeeze throttle to provide fuel to engine.

To stop the engine, depress the STOP switch to the 

stop position “STOP”.

NOTE:

 This Stop switch will come back to the ON 

position automatically.
IF ASSISTANCE IS REQUIRED FOR THIS PRODUCT:

Do not return this product to the retail store where it 

was purchased. Please call our Customer Service 

Department for any issues you may have. For Help 

Call: 1-800-261-3981

Throttle Control

On/Off Switch

(I = On / STOP = Off)

Throttle

Lockout

Primer Bulb

Choke

Starting

Position

Starter Rope Grip

Throttle Control

Summary of Contents for CSP4QL-L





























































Reviews: