Sena 10s User Manual Download Page 10 | Manualshive

Page: 10 / 58

Sena 10s User Manual Download Page 10

10S

10

3.1.2 Using the Glued Surface Mounting Adapter

If you cannot install the clamp unit on the helmet, you can use the

glued surface mounting adapter to attach the clamp unit to the surface

of the helmet.
1. Clean the area on the left side of the helmet where you will attach

the glued surface mounting adapter with a moistened towel and
dry thoroughly.

2. Peel off the cover of adhesive tape of the glued surface mounting

adapter and attach it to the helmet.

3. Make sure that the glued surface mounting plate sticks on the

helmet firmly. Maximum adhesion occurs after 24 hours.

4. Attach the clamp unit on the glued surface mounting adapter

using two screws.

1

2

CAUTION:

Sena recommends using the clamp unit. The glued surface mounting
adapter is provided for convenience, but is not the recommended mounting
method. Sena is not responsible for its use.

5. Attach the main unit to the glued surface mounting adapter until

you hear a click. The main unit is now fastened to the clamp unit.

«
...
8
9
10
11
12
...
»

Summary of Contents for 10s



























































Reviews:

No comments