semaphore KINGFISHER PLUS+ Hardware Reference Manual Download Page 35 | Manualshive

Page: 35 / 247

semaphore KINGFISHER PLUS+ Hardware Reference Manual Download Page 35

Kingfisher Plus+ Hardware Manual

3.

POWER SUPPLY MODULES

Overview

The Kingfisher Plus+ Power Supply Modules allow real time monitoring of currents, voltages
and temperatures supplied to the RTU and the backup battery. The monitoring capability
also allows the RTU to determine when a supply has failed if in a redundant configuration.

If fitted, auxiliary supplies can be overridden manually or by logic to allow for external
equipment or sensor loops to be shut down or reset.

PS-x2 and PS-x1 Power Supply Modules

3.2.1 Overview

•

Monitoring of rail voltages, supply & battery currents and temperature

•

AC or DC input

•

Support for redundancy (several supplies per backplane)

•

Isolated DC output

•

Sealed Lead Acid battery connection with charging/monitoring and low voltage

protection

•

Software controlled power to the Backplane and Aux Outputs

Note: PS-x1 is a SUPERSEDED product and is not being manufactured currently.

Fire Risks

A supply voltage outside the specified limits

may cause fire.

Risques d'Incendie

Une tension d’alimentation en dehors des limites spécifiées peut

provoquer un incendie.

Hardware Manual Version 7.16

http://www.servelec-semaphore.com/

Page 35

«
...
33
34
35
36
37
...
»

Summary of Contents for KINGFISHER PLUS+
























































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands