background image

 

DT-E 1.3: SUN PROTECTION SCREEN – VENETIAN BLINDS C80P and C80L                                                                                                                                                        
Issue 3 / April 2017 / EN                                                                                                                                                                 

 

        page 5 / 62                                                                                    

 

 

 

 

 

 

           

1.3.

 

DEFINITIONS 

 
The following terms and definitions used within this documentation shall mean:  

Product : Venetian Blind C80 and C80 L 
 
VENETIAN  BLIND: 

The  external  sun  protection  system,  installed  outside  the  building,  over  or  inside  the  window  opening 

building in which lifting and dropping of the aluminum slats is made by the operating mechanism (manual with hand crank, 
electric with drive connected to the steering system. 

 

 
SLATS: 

Part of the product, made of aluminum stripes, that is moved by a steering mechanism, that ensures the product 

fulfills its function.

 

 

1.4.

 

SUBJECT, DESIGNATION AND CONTENTS OF THE  DOCUMENTATION  

 

Products manufactured by  

SELT Sp. z o. o. 

are the subject of this documentation. 

 

 

Operating  manual  and  instructions  for  safe  use  along  with  the  manual  for  the  engine,  switches 
and control shall be submitted to the end user. 

 

 

 

IMPORTANT INFORMATION REGARDING SAFETY 

WARNING – FOLLOWING THE MANUAL IS ESSENTIAL FOR SAFETY OF PEOPLE 

KEEP THIS MANUAL 

 
 

 

 
The documentation is valid jointly with the information concerning a specific product, which is 
available on the website 

www.selt.com

 

 

 

The documentation includes: 

 

important recommendations concerning product installation, use and maintenance, 

 

important recommendations concerning product transport and storage, 

 

tips following which will assure long-time and fault-free use of the product. 

SELT Sp. z o. o. shall not bear responsibility for damage resulting from failure to follow recommendations included in the 
documentation. 

In order to further improve the product, SELT Sp. z o. o. reserves the right to introduce changes which, while maintaining 
the essential technical parameters, shall be deemed purposeful for improving product operation quality and safety of use.  

SELT Sp. z o. o. with a head office in Opole shall hold the copyrights to this documentation. The documentation cannot be 
used without permission, either partially or as a whole, for any concurrent business activity nor can it be made available to 
third parties. 

 

Summary of Contents for Venetian Blind C80































































Reviews: