manualshive.com logo in svg

Sekonic LITEMASTER PRO L-478DR-A-PX, Operating Manual, Page: 12 / 68

Share
Download
Sekonic LITEMASTER PRO L-478DR-A-PX Operating Manual Download Page 12

12

3 

Screen Operations

The data display is also a touch panel that is used to make all settings. 
<Display illumination>

•

 The Display illumination is activated as soon as the meter is turned ON. The 

illumination level is user adjustable. The panel dims during measuring and cordless 

flash standby to eliminate its influence in the measurement. 

•

 The display Illumination of your meter has been set to “Bright” at the factory to enable 

best operation for outdoor use.For indoor viewing and better battery life, you may set 

the screen illumination to “Normal” in Custom Setting. Please see P51 for details.

3-1. On-screen Operations

Touch the icons on screen to perform various operations. 
The following are the icon types. 
1)  Measuring Mode Icon

   Touch the Measuring mode icon to display the Measuring Mode Selection screen. 

Touch any icon to switch to the desired Measuring mode. (See P25 for details.)

Measuring Screen

Measuring Mode Selection Screen

2)  Setting Value Change/Item Selection Icon 

Touch Operation:

Touch the up arrow (

▲

) to increase the value or change up to the next item. 

Touch the down arrow (

▼

) to decrease the value or change down to the next item. 

Slide Operation:

Slide your finger tip up or down over the value to change the value amount.
Sliding your finger over scroll bars provides fast navigation of large menus.

Measuring Screen

Scroll bar

Edit Frame Rate Screen 

Summary of Contents for LITEMASTER PRO L-478DR-A-PX





































































Reviews:

No comments