manualshive.com logo in svg

Seiko Astron 3X22, Complete User Manual, Page: 34 / 50

Share
Download
Seiko Astron 3X22 Complete User Manual Download Page 34

Some bands are provided with an adjustable three-fold

clasp.
If the clasp of the watch you purchased is as follows,

please refer to the following instructions.

1

Press the push buttons on both sides of

the flap; pull the buckle up. The band will

automatically come out of the loop.

Fixed loop

Movable loop

Buckle

Flap

Push button

2

Place the tip of the band into the movable

loop and fixed loop, and fasten the clasp

by pressing the frame of the buckle.

1

Press the push buttons on both sides of

the flap; pull the buckle up. The band will

automatically come out of the loop.

Fixed loop

Movable loop

Buckle

Flap

Push button

2

Press the push buttons again to unfasten

the flap.

3

Pull the pin out of an adjustment hole of

the band. Slide the band to adjust its

length and find an appropriate hole. Place

the pin into the hole.

Pin

Adjustment hole

4

Fasten the flap.

●

How to wear or take off the watch

●

How to adjust the length of the band

 * The above illustrations are provided as examples. Some details may differ depending on the model.

How to use an adjustable three-fold clasp

33

6

TO PRESERVE THE QUALITY OF YOUR WATCH

ASTRON 3X22 GPS SOLAR

Summary of Contents for Astron 3X22



















































Reviews:

No comments