instructions for
description. dual action palm sander Ø125mm
240w/230v
model no:
s0125
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFetY
1.1. electrical safety
warninG!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the lamp is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3.
important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
do not
pull or carry the appliance by the power cable.
8
do not
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
do not
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
qualified electricia
n.
1.1.4.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
class ii products are wired with live (brown) and neutral (blue) only are marked with the class ii symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
c) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
do not
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2. General safety
warninG!
ensure that Health & safety, local authority and general workshop practice regulations
are adhered to when using this sander
1.2.1. familiarise yourself with the application, limitations and potential hazards of the sander.
warninG!
disconnect from the mains power and ensure that the pad is at a complete standstill before changing accessories,
servicing or performing any maintenance.
1.2.2. maintain the sander in good condition (use an authorised service agent).
1.2.3. replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
warninG!
Keep all holding screws in place, tight and in good working order. check regularly for damaged parts.
A part that is damaged must be repaired/replaced before the sander is next used.
1.2.4. use the sander in a suitable work area and keep the area clean and tidy and free from unrelated
materials. ensure that there is adequate lighting.
1.2.5. Keep the sander clean for best and safest performance.
1.2.6. Before each use check all attachments for condition. If worn or damaged replace immediately.
1.2.7. ensure that there are no flammable materials near the work area.
1.2.8.
warninG!
Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
1.2.9. maintain correct balance and footing. ensure that the floor is not slippery and wear non-slip shoes.
recommended fuse rating
5 Amp
refer to
instruction
manual
W
ear eye
Protection
s
0125 | Issue 2 21/02/17
Original Language Version
© Jack sealey limited
W
ear
Protective
Gloves
W
ear a
mask
W
ear ear
Protection
