manualshive.com logo in svg

Seeing Machines G2-SY-CON2, Support Manual, Page: 86 / 110

Share
Download
Seeing Machines G2-SY-CON2 Support Manual Download Page 86

Guardian Field Support Manual – Section 2 

 

58 

 

6.1  APPLYING LATEST SOFTWARE TO THE CONTROLLER 

 

Software Installation

 

The Software (SW) Installation is to be conducted once you have completed installing all the 

Hardware components.  As the system needs to be configured, all components (except for the 

processor) need to be in their final location. 
You will upload the SW using a USB Recovery Dongle (

refer to Section 3.5

). 

The latest version of the SW will be available via the TCP in the Knowledge Base.  Certified 

Installers can navigate to Guardian Generation 2 > Gen 2 Downloads/Forms where the 

Recovery Dongle Creator and SW release notes will be found. 

Un-isolate the vehicle and ensure the 

ignition is ‘off’. 

 

Insert the USB Recovery Dongle into the 

USB port on the Controller. 

 

Turn the ignition to ‘On’.  The Controller will 

now power up and commence applying the 

SW. 
 

 

 

 

Summary of Contents for G2-SY-CON2















































































































Reviews:

No comments