manualshive.com logo in svg

Seeing Machines G2-SY-CON2, Support Manual, Page: 66 / 110

Share
Download
Seeing Machines G2-SY-CON2 Support Manual Download Page 66

Guardian Field Support Manual – Section 2 

 

38 

 

5.4.5  3/4G ANTENNA INSTALLATION 

3/4G Antenna 

 

Mounting Location: 

The 3/4G antenna must be mounted so that there is a clear line of sight to the sky. 
The 3/4G antenna can transmit through plastic, wood and fiberglass. 
It cannot transmit through metal. 
It is recommended that you mount the antenna as close to a window as possible.  The shape of 

the antenna allows you to mount it close to the windscreen. 

 

Mount the 3/4G antenna at least 30cm from 

the GPS Antenna. 
Mount the 3/4G antenna at least 60cm from 

the ICS and any other antennas, such as 3

rd

 

party GPS systems and communication 

antennas 
Mount the antenna at least 1m from the 

Controller. 

 

Types of Mounting: 

The 3/4G Antenna comes with adheisive 

tape for mounting.  
You must clean the area with the provided 

alcohol wipe and allow it dry for 1 minute 

before mounting. 
Ensure you firmly press down on the 

Antenna for 30 seconds. 

 

Important Points to Note: 

Summary of Contents for G2-SY-CON2















































































































Reviews:

No comments