Seeing Machines G2-SY-CON2 Support Manual Download Page 46

Page: 46 / 110

4 PREPARATION FOR INSTALLATION

This chart shows an overview of the steps required to successfully complete an installation

Call Site before arrival

•

Client has Nano SIM Cards

•

SIM Cards are activated

•

Confirm arrival time

•

Confirm opening hours

•

Confirm vehicle availability

SIM Card Collection

•

Pickup SIM cards from the

installation site contact

•

Nano SIM cards are

required

•

Ensure they are activated

and unlocked by the Client

Installation Requirements

•

Check against the Job Card

if you have been provided

one, to see if there are any

special installation requests

including Hard or Soft

Installation

Installer Kit

•

Security T20 Key

•

24/7 Support Contact Card

•

USB to Ethernet adapter

•

Ethernet Cable

•

Gen 2 Programmed USB

Recovery Dongle

Customer Configuration

•

Ensure you have the latest

Configuration file for your

site and customer settings.

Package & Contents

•

Check packaging to make

sure you have all required

parts to complete your

installation

•

Check if you are installing

Optional Extras as per the

Job Card

Paperwork - Checklist / Job card

•

Fill in the information

requested on this document

before commencing the

installation.

Pre-installation Photos

•

For insurance reasons

photos should be taken

inside the vehicle before

installation

•

This will provide evidence

for any insurance claims

Safety Requirements

•

Make sure all site safety

rules are followed before

commencing the

installation

•

Ensure you have all

Personal Protection

Equipment (PPE)

according to site safety

rules

•

Ensure all site inductions

are performed prior to

arrival

Pre-Installation

Summary of Contents for G2-SY-CON2















































































































Search results

Summary of Contents for G2-SY-CON2

Reviews:

Seeing Machines G2-SY-CON2, Support Manual, Page: 46 / 110

Search results

Summary of Contents for G2-SY-CON2

Reviews: