Technical data
38 / 40
ASD 535, Mounting and installation, T 140 333 d en
5
Technical data
Type
ASD 535
Supply voltage range
10.5 to 30 (
UL/FM = 12.4 to 27
)
VDC
Max. power consumption, measured in
12 VDC operation
24 VDC operation
Typical
Fan speed level V and at
10.5 VDC
18 VDC
24 VDC
ASD 535-1
Idle/fault
approx. 575
approx. 340
approx. 260
mA
Alarm I
approx. 660
approx. 390
approx. 295
mA
ASD 535-2
Idle/fault
approx. 645
approx. 380
approx. 290
mA
Alarm I + II
approx. 745
approx. 450
approx. 350
mA
ASD 535-3
Idle/fault
approx. 575
approx. 340
approx. 260
mA
Alarm I
approx. 695
approx. 405
approx. 310
mA
ASD 535-4
Idle/fault
approx. 645
approx. 380
approx. 290
mA
Alarm I + II
approx. 820
approx. 490
approx. 385
mA
additionally with 1 RIM 35 units
approx. 15
approx. 10
approx. 7
mA
additionally with 2 RIM 35 units
approx. 30
approx. 20
approx. 14
mA
additionally with XLM 35 / SLM 35
approx. 20
approx. 10
approx. 5
mA
additionally with MCM 35
approx. 25
approx. 15
approx. 10
mA
additionally with SIM 35
approx. 20
approx. 10
approx. 5
mA
SMM 535 (not from ASD but rather from PC via USB connection)
max. 100
mA
Switch-on current peak
(caused by EMC protection elements on the ASD supply input)
approx. 5
A
for max. 1
ms
Sampling pipe length
see T 140 421
Sampling pipe Ø, typical (inner/outer)
Ø 20 / 25
mm
Max. number of sampling holes
see T 140 421
Sampling hole diameter
Ø 2 / 2.5 / 3 / 3.5 / 4 / 4.5 / 5 / 5.5 / 6 / 6.5 / 7
mm
Response range (smoke sensor sensitivity see Sec.
EN 54-20, class A, B, C
Protection type acc. to IEC 529 / EN 60529
54
IP
Ambient conditions acc. to IEC 721-3-3 / EN 60721-3-3
3K5 / 3Z1
class
•
Extended ambient conditions:
•
Detector housing temperature range
–30 – +60 (
UL max. +40
)
°C
•
Temperature range of detector housing to Australian Standard AS 1603.8
–30 – +55
°C
•
Sampling pipe temperature range
–30 – +60
°C
•
Temperature range of sampling pipe to Australian Standard AS 1603.8
–30 – +55
°C
•
Max. approved temperature fluctuation in detector housing and sampling pipe operation
20
°C
•
Max. permitted storage temperature of detector housing (without condensation)
–30 – +70
°C
•
Ambient pressure difference of detector housing to sampling pipe (sampling holes)
must be identical
•
Detector housing humidity ambient condition (transient without condensation)
95
% rel. hum.
•
Detector housing and sampling pipe humidity ambient condition (continuous)
70
% rel. hum.
Max. loading capacity relay contact
50 VDC (
UL max. 30
) / 1 A / 30 W
Max. loading capacity per open collector output (electrical strength 30 VDC)
100
mA
Plug-in terminals
2.5
mm²
Cable entry for cable Ø
Ø 5 – 12 (M20) / Ø 9 – 18 (M25)
mm
Sound pressure level for fan speed level I / II / III / IV / V
34 / 36 / 39 / 40 / 41 dB (A) / 1 m
Housing
material
ABS blend, UL 94-V0
colour
grey 280 70 05 / anthracite violet 300 20 05
RAL
Approvals
EN 54-20 / EN 54-27 / FM 3230-3250 / UL 268 / UL 268A / ULC-S529
Dimensions
ASD 535-x (W x H x D)
265 x 397 x 148
mm
Weight
ASD 535-x (incl. SSD 535-x)
3,555
g
Notices
Power consumption at maximum permitted voltage drop in the electrical installation (guideline value for calcu-
lating the conductor cross-Sec.).
May cause an immediate actuation of the protection circuit in power supplies with overload protection circuits
(primarily in devices with no emergency power supply and output current of < 1.5 A).
Lower or higher temperature ranges are possible after consulting with the manufacturer. The manufacturer
must be consulted if deployment is to be in the condensation range.
Summary of Contents for ASD 535
Page 4: ......