Sebart KatanaS 30E Assembly Manual Download Page 6 | Manualshive

Page: 6 / 19

background image

6

Section 2 – ailerons installation

step 1

Trial fit the four aileron hinges, included in the hardware pack, in their place and verify the correct
position and alignment of the aileron with the wing panel.

step 2

Carefully glue, with some drops of thin CA, each of the four hinges in the aileron.

«
...
4
5
6
7
8
...
»

Summary of Contents for KatanaS 30E




















Reviews:

No comments

Related manuals for KatanaS 30E

Brand: Lancair Pages: 8

Brand: E-FLITE Pages: 17

Habu 32 EDF ARF

Brand: E-FLITE Pages: 56

Brand: FB Jets Pages: 39

Zlin Z-37A Cmelak

Brand: KOR MODEL Pages: 21

Brand: Viessmann Pages: 2

BN TWIN HIGHCHAIR

Brand: Smoby Pages: 4

Brand: Rail King Pages: 27

SmartControl light

Brand: PIKO digital Pages: 8

Brand: GAME OF BRICKS Pages: 31

Brand: le-idea Pages: 2

MESSERSCHMITT BF 110 C

Brand: Flying Styro Kit Pages: 16

The Lone Ranger

Brand: Lionel Pages: 24

Brand: J. Perkins Pages: 12

BEAR AND THE STARS

Brand: Chipolino Pages: 4

Brand: Eduard Pages: 7

A-7D/E Corsair II

Brand: Jet Hangar Pages: 66

V.Smile Learnin' Wheels

Brand: VTech Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands