Refer to
instruction
manual
Wear
protective
footwear
Beware
crushing of
hands
Wear eye
protection
Steel frame construction with hydraulic pump unit. Sliding hydraulic ram assembly
gives 176mm of lateral travel for off-centre pressing applications. Frame head fitted
with ram pressure gauge. Supplied with flat pressing plate/V-blocks.
1.1
GENERAL SAFETY
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
Maintain the
press in good condition (use an authorised service agent).
Replace or repair damaged parts.
Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
Keep the press clean for best and safest performance.
Locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is
adequate lighting.
Ensure the workpiece is correctly secured before operating the press.
WARNING!
Always wear approved eye or face protection when operating the press.
Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.
Keep hands and body clear of the work table when operating the press.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip steel toe-capped shoes/boots.
Keep children and unauthorised persons away from the working area.
DO NOT
operate the press if any parts are missing as this may cause failure or possible personal injury.
DO NOT
use to compress springs or any other item that could disengage and cause a potential hazard.
DO NOT
stand directly in front of the loaded press and never leave a loaded press unattended.
DO NOT
force the press to achieve a task it was not designed to perform.
DO NOT
make any modifications to the press.
DO NOT
adjust or tamper with the safety valve.
DO NOT
exceed the rated capacity of the press.
DO NOT
apply off centre loads.
DO NOT
allow the workpiece or the arbor plates to fall from the press working bench.
DO NOT
get the press wet or use in damp or wet locations or areas where there is condensation.
DO NOT
operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.
When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.
WARNING! Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be
placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
DANGER! The press is top heavy
. If it requires moving after assembly or for relocation, use suitable slings around the top crossbeam, or
lift direct with a forklift with the forks located under the top crossbeam.
DO NOT
use a pallet truck.
INSTRUCTIONS FOR:
HYDRAULIC PRESS 20TONNE FLOOR TYPE
MODEL No
:
YK209F.V2
Model No: . . . . . . . . . . .YK209F
Capacity: . . . . . . . . . . . .20tonne
Ram Stroke:. . . . . . . . . . .180mm
*Ram Mandrel Diameter: . . . .50mm
Lateral Ram Travel: . . . . . . .176mm
Max Height Ram to Table: . . .912mm
Min Height Ram to Table: . . . .35mm
Table Aperture: . . . . . . . . .155mm
Working Table Depth: . . . . . .175mm
Working Table Width: . . . . . .510mm
Overall Height: . . . . . . . . .1619mm
Weight: . . . . . . . . . . . . .105kg
Safety Guard (Optional): . . . .YKSG20
* Gauge specifies 'ram diameter' is 60mm. This refers to the internal diameter of the ram and
is correct. It does not refer to the working mandrel diameter.
Original Language Version
YK209F.V2 Issue: 4(L) - 09/05/17
© Jack Sealey Limited
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. SPECIFICATION
