Sealey YK15, Instructions

Page: 1 / 2

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION & SPECIFICATIONS
FLOOR Models: YK15, YK15FM, YK30, YK30FM, YK50FM.
BENCH Models: YK10BM, YK15BLG, YK15BM.
1. SAFETY INSTRUCTIONS
2.1. GENERAL INFORMATION
The Sealey range of heavy duty floor and bench hydraulic presses are ideal for a variety of workshop applications and are particularly suited
to agricultural or industrial use. Jobs such as straightening, bending, folding, punching, removing bolts and bearings etc are some of tasks that
may be accomplished by your press. All models are fitted with pressure gauge and work-table V-blocks except where stated. The “BM” and “FM”
range of press units feature integrally mounted rams giving more vertical clearance between the table and ram head enabling larger items
to be fitted on the working table.
p
p
p
p
WARNING! All models are purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
ensure the workpiece is secured on table and loads that flex will not suddenly “give” causing danger to operator or damage to component.
1.2 GENERAL SAFETY
3 Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.
3 Maintain the press in good condition (use an authorised service agent).
3 Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
3 Keep the press clean for best and safest performance.
3 Locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and ensure
there is adequate lighting.
3 Ensure the workpiece is correctly secured before operating the press.
p WARNING! Always wear approved eye or face protection when operating the press.
3 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
3 Keep hands and body clear of the work table when operating the press.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
3 Keep children and unauthorised persons away from the working area.
7 DO NOT operate the press if any parts are missing as this may cause failure or possible personal injury.
7 DO NOT force the press to achieve a task it was not designed to perform.
7 DO NOT adjust or tamper with the safety valve.
7 DO NOT exceed the rated capacity of the press.
7 DO NOT apply off centre loads.
7 DO NOT allow the workpiece of the arbor plates to fall from the press working bench.
7 DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.
7 DO NOT operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.
3 When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.
Unpack product and check contents against list below . Should there be any damaged or missing parts contact your supplier immediately.
Take care to ensure safety when removing main frame from packing as the unit is very heavy. Retain pressure gauge in carton until required,
and do not remove white tape from gauge mount or masking tape from the angle arm.
Contents:
3 Frame 3 legs x2 3 worktable x1 3 worktable pins x2 3 v-blocks x2 3 pump handle x1 3 pressure gauge x1 ( except model YK15BLG )
3 gauge angle arm connector x1. 50Ton models incorporate winch handle.
3.1. Press Assembly
3.1.1. Identity and lay out parts. Handle the main frame with care and lay horizontally allowing the cross legs to be bolted on to the bottom
of the pre-assembled main frame. Note: care must be taken when handling the main frame to ensure stability. DO NOT allow to fall.
3. ASSEMBLY
INSTRUCTIONS FOR:
HYDRAULIC BENCH & FLOOR PRESS
2.2. SPECIFICATIONS
Model: YK15BLG YK10BM YK15BM YK15 YK15FM YK30 YK30FM YK50FM
Capacity 15T 10T 15T 15T 15T 30T 30T 50T
Ram Stroke 150mm 95mm 95mm 150mm 95mm 150mm 95mm 95mm
Extension screw 60mm 70mm 70mm 60mm 67mm 60mm 70mm 70mm
Ram to table 300mm 455mm 455mm 600mm 600mm 600mm 620mm 615mm
Min Ht-Ram to table 150mm 155mm 155mm 150mm 150mm 150mm 180mm 165mm
Table Aperture 112mm 140mm 140mm 112mm 140mm 133mm 143mm 170mm
Work table width 500mm 500mm 500mm 500mm 500mm 550mm 550mm 550mm
Overall Height 945mm 1035mm 945mm 1675mm 1650mm 1750mm 1750mm 1830mm
Gauge Included no yes yes yes yes yes yes yes
Weight 69kg 65kg 69kg 80kg 86kg 122kg 125kg 240kg
YK10BM, YK15, YK15BLG, YK15BM, YK15FM, YK30, YK30FM, YK50FM. - 0025 - 050897