Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
bEARING & bUSH REMOVAL/
INSTALLATION KIT 27pcs
MODEL No:
VS7026
1.1 GENERAL SAFETY
WARNING!
Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
tool.
WARNING!
Familiarise yourself with the specific applications
and limitations of the kit, as well as any potential hazards.
This kit should be used in conjunction with inspection
maintenance procedures recommended in the vehicle
manufacturer’s manual.
Ensure that the kit is correct for the task.
Wear the appropriate personal protective equipment for the
task. A full range is available from your Sealey dealer.
DO NOT
use the kit
for any purpose other than that for which it
is designed.
Ensure that the vehicle is properly supported with axle stands
before working under the vehicle.
Ensure there is adequate lighting prior to using the kit. A range
of inspection lamps are available from your Sealey dealer.
Keep children and unauthorised persons away from the working
area.
DO NOT
use the kit if any parts are damaged or missing, as this
may cause failure and/or personal injury.
DO NOT
use the kit
when you are tired, or under the influence of
alcohol, drugs or intoxicating medication.
After use, store in a safe, dry childproof area.
ALWAYS KEEP FORCE SCREW
WELL LUbRICATED. MOLYbDENUM/
COPPER bASED GREASE
RECOMMENDED.
DO NOT USE AIR TOOLS
1. SAFETY INSTRUCTIONS
2. INTRODUCTION
The force screw maximum recommended torque is 170Nm (M18x1.5), 155Nm (M16X1.5), 99Nm (M14X1.5), 60Nm (M12X1.5), 33Nm (M10X1.5).
Exceeding these torque values may shorten the life of the force screws. The force screws are considered to be consumable items and are
NOT covered under warranty.
Comprehensive kit for fast and effective in-situ removal/installation of wheel bearings/suspension bushes and seals.
Reduces the possibility of damaging the bearing/suspension housings. Supplied with twenty two adapters from 44 to
90mm and five force screws in carry case. Adapters can also be used in a standard workshop press when in situ
access isn't possible.
3. CONTENTS
3.1 Adapters
External Ø mm Internal Ø mm Part No.
44
34
VS7026.01
46
36
VS7026.02
48
38
VS7026.03
50
40
VS7026.04
52
42
VS7026.05
54
44
VS7026.06
56
46
VS7026.07
58
48
VS7026.08
60
50
VS7026.09
62
52
VS7026.10
64
54
VS7026.11
66
56
VS7026.12
68
58
VS7026.13
70
60
VS7026.14
External Ø mm Internal Ø mm Part No
72
62
VS7026.15
74
64
VS7026.16
76
66
VS7026.17
78
68
VS7026.18
80
70
VS7026.19
82
72
VS7026.20
85
75
VS7026.21
90
80
VS7026.22
3.2 Force Screws
Size
Part
No.
M10
VS7026.23
M12
VS7026.24
M14
VS7026.25
M16
VS7026.26
M18
VS7026.27
Fig.1
VS7026 Issue No.1 - 07/03/13
Original Language Version
© Jack Sealey Limited
Summary of Contents for VS7026
Page 3: ......
