INSTRUCTIONS FOR:
BEARING & BUSH REMOVAL/
INSTALLATION KIT 27pc
MODEL No:
VS7026.V2
1.1.
GENERAL SAFETY
WARNING!
Ensure Health & Safety, local authority, and general workshop
practice regulations are adhered to when using this tool.
WARNING!
Familiarise yourself with the specific applications and limitations of
the kit, as well as any potential hazards.
This kit should be used in conjunction with inspection maintenance procedures
recommended in the vehicle manufacturer’s manual.
Ensure that the kit is correct for the task.
Wear the appropriate personal protective equipment for the task. A full range is
available from your Sealey dealer.
DO NOT
use the kit
for any purpose other than that for which it is designed.
Ensure that the vehicle is properly supported with axle stands before working under
the vehicle.
Ensure there is adequate lighting prior to using the kit. A range of inspection
lamps are available from your Sealey dealer.
Keep children and unauthorised persons away from the working area.
DO NOT
use the kit if any parts are damaged or missing, as this may cause
failure and/or personal injury.
DO NOT
use the kit
when you are tired, or under the influence of alcohol, drugs or
intoxicating medication.
After use, store in a safe, dry childproof area.
ALWAYS KEEP FORCE SCREW
WELL LUBRICATED. MOLYBDENUM/
COPPER BASED GREASE
RECOMMENDED.
DO NOT USE AIR TOOLS
The force screw maximum recommended torque is 170Nm (M18x1.5), 155Nm (M16X1.5), 99Nm (M14X1.5), 60Nm (M12X1.5), 33Nm (M10X1.5).
Exceeding these torque values may shorten the life of the force screws. The force screws are considered to be consumable items and are
NOT covered under warranty.
Comprehensive kit for fast and effective in-situ removal/installation of wheel bearings/suspension bushes and seals. Reduces the possibility of
damaging the bearing/suspension housings. Supplied with twenty two adapters from 44 to 90mm and five force screws in carry case. Adapters can
also be used in a standard workshop press when in situ access isn't possible.
3.1. Adapters
External Ø mm Internal Ø mm Part No.
44
34
VS7026.01
46
36
VS7026.02
48
38
VS7026.03
50
40
VS7026.04
52
42
VS7026.05
54
44
VS7026.06
56
46
VS7026.07
58
48
VS7026.08
60
50
VS7026.09
62
52
VS7026.10
64
54
VS7026.11
66
56
VS7026.12
68
58
VS7026.13
70
60
VS7026.14
External Ø mm Internal Ø mm Part No
72
62
VS7026.15
74
64
VS7026.16
76
66
VS7026.17
78
68
VS7026.18
80
70
VS7026.19
82
72
VS7026.20
85
75
VS7026.21
90
80
VS7026.22
3.2. Force Screws
Size
Part
No.
M10
VS7026.23
M12
VS7026.24
M14
VS7026.25
M16
VS7026.26
M18
VS7026.27
Fig.1
VS7026.V2 Issue No.1 - 02/02/15
Original Language Version
© Jack Sealey Limited
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
2. INTRODUCTION
3. CONTENTS
Refer to
instruction
manual
Summary of Contents for VS7026.V2
Page 3: ......
