background image

Motorcycle Wheel Balancer

Model no: 

VS1819.V3

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  Safety

   

General Safety

 

‰

 

 

WarnInG!

 

Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this  

 

  equipment. Under Health and Safety Law, Employers and Self Employed Personnel have a legal duty to ensure Safe Working  

 

  Conditions for all employees and personnel that may come into contact with this equipment. In particular they must carry out a specific  

  risk and hazard assessment in the workplace to eliminate or reduce any risk found and must record, update and retain records of the  

  results of this inspection.

 

9

 

  Familiarise yourself with the applications, limitations and any possible or potential hazards of the Wheel Balancer.

 

9

   Maintain  the

 

Wheel Balancer in good condition.

 

9

   Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 

‰

  

WarnInG!

 Check regularly for damaged parts. Any part that is damaged must be repaired or replaced before the equipment is  

 

  next used. 

 

9

   locate the Wheel Balancer in a suitable work area, keep area clean and tidy and free from unrelated materials. 

 

9

   ensure that there is adequate lighting.

 

9

   Keep the Wheel Balancer clean for best and safest performance.

 

9

   Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.

 

9

   Keep children and unauthorised persons away from the work area.

 

8

  

Do not

 use the Wheel Balancer for any purpose other than that for which it is designed.

 

8

  

Do not

 operate the Wheel Balancer if any parts are damaged or missing as this may cause failure and/or personal injury.

2.  IntroDuctIon

Professional Motorcycle Wheel Balancer. Suitable for most motorcycle wheels. Includes two cones and spindle for precise, easy alignment and 

balancing. Uses gravity to find the heavy point of a wheel and tyre. 

3.  SpecIfIcatIon

Maximum Cone Size: ................................................ Ø35mm

Centre Spindle to Base: ............................................. 400mm

4.  aSSeMBly

4.1.    

Place the uprights onto the base (with the bearings facing inwards). Secure to the base as shown in fig.1 below using two 13mm bolts,  

 

two washers and two 13mm nuts. You will require two 13mm spanners to hold the nuts steady and to tighten the bolts. 

4.2.    

Place the bubble indicator over the hole in the base and align the three holes in its flange with the three holes in the base. Secure with  

 

the 3 small screws and nuts supplied. See fig.2.

4.3.    

Thread a 13mm nut onto each foot and screw it down to the bottom of the thread but leave it loose.

4.4.    

Screw the 4 feet into the base of the balancer, as shown in fig.1. Adjust the feet until the bubble indicator shows that the base is level. 

4.5.    

Fix the positions of all four feet by tightening up the 13mm nut to the underside of the metalwork.

VS1819.V3 Issue 2 14/05/18

Original Language Version

© Jack Sealey limited

Refer to 

instructions

   fig.1

Reviews: