ADBLUE® TRANSFER PUMPS PORTABLE
12V, 230V
MODEL NO:
TP9912, TP99230
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING!
It is the user’s responsibility to check the following:
1.1.1.
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
1.1.2.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.3.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.4.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
8
DO NOT
pull or carry the appliance by the power cable.
8
DO NOT
pull the plug from the socket by the cable.
8
DO NOT
use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is
replaced immediately by a qualified electrician.
1.1.5.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
1.1.6.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
1.1.7.
Ensure that repairs are carried out by a qualified electrician.
1.1.8.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.1.9.
If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred
since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be
absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we
recommend the use of 2.5mm² section cable.
S
1.2.
GENERAL SAFETY
WARNING!
Ensure health & safety, government and local authority regulations relating to the transfer of AdBlue
®
are adhered to when
using this equipment. Familiarise yourself with the pump’s applications and limitations, and specific potential hazards peculiar to the
pump.
WARNING!
These pumps are designed for use with urea and aqueous media only.
DO NOT use for petrol or similar explosive liquids.
▲
DANGER: The electric pump is not protected against explosion and should therefore not be operated in areas where there
is a risk of explosion.
WARNING!
Disconnect the pump from the mains or battery power before demounting, servicing or performing any maintenance.
9
Maintain pump in good condition (use authorised service agent).
Drain pump and pipes before dismantling.
9
Maintain correct balance and footing when installing and using the pump. Ensure the floor is not slippery and wear non slip shoes.
9
Ensure the transfer area is free of clutter and has adequate lighting.
9
Ensure that the voltage of the pump matches the voltage of the supply.
9
Keep children and unauthorised persons away from the working area.
9
Replace/repair damaged parts. Use genuine parts. Unauthorised parts are dangerous and will invalidate warranty.
8
DO NOT
use the pump without the delivery nozzle attached.
8
DO NOT
start or stop the pump by switching on or off at the mains power supply. or disconnecting from battery.
8
DO NOT
operate the unit with wet hands.
We recommend use of chemical resistant gloves and goggles.
8
DO NOT
run the pump dry. If this occurs the pump could be damaged and your warranty will be invalidated.
IMPORTANT:
It is the installer’s responsibility to ensure that all supply pipes, fixtures and fittings are adequate for the safe flow of liquid
urea.
Refer to
instruction
manual
Wear goggles Wear protective
gloves
Original Language Version
© Jack Sealey Limited
Recommended fuse rating
13 Amp (TP99230)
T
P9912, TP99230 | Issue:2 (H,F) 26/10/18
