WARNING!
Pump must be used in accordance with Health & Safety, government, local authority, and water authority rules
and regulations.
Familiarise yourself with application and limitations, as well as the potential hazards peculiar to the pump.
WARNING!
Disconnect the pump from the battery before changing accessories, servicing or performing any maintenance.
Maintain the
pump in good condition. Keep the pump clean.
Replace or repair damaged parts (use an authorised service agent).
Use genuine parts only. Non authorised parts may be
dangerous and will invalidate the warranty.
If the bottom of the liquid container is covered with sludge, sand, gravel or mud etc, suspend the pump or place it on a raised
base to operate above the solid matter. Sand and such substances will reduce working life of pump, and invalidate your
warranty.
In flood situations, user is responsible for ensuring that appropriate back up procedures, alarms etc are correctly installed in
case of pump failure.
In swimming pool, fish ponds, etc, ensure location is clear of people and animals (including removal of fish from pond).
Note: this pump is not designed for continuous use in a fish pond or similar water feature or display.
DO NOT
use with petrol or other volatile liquids within flashpoint range -20°C to +80°C.
DO NOT
use to pump septic tanks or settling pits.
DO NOT
operate the pump if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT
use the pump for any purpose other than for which it is designed.
DO NOT
operate pump out of liquid. The pump pick up area must be completely submerged during operation.
DO NOT
operate the pump during freezing temperatures.
DO NOT
leave the pump in water that may freeze.
DO NOT
carry the pump by its electrical cable, or outlet pipe.
When not in use remove battery clips from terminals. Rinse pump, drain out any liquid and store in a frost free, safe location.
WARNING! Whilst the pump may be used in dirty water, it is not to be used for water containing large particles e.g. mud, weed
etc.
WARNING! DO NOT allow uncontrolled discharge of contaminated water/harmful chemicals thus polluting the environment.
WARNING! This pump must only be connected to a 24Vdc battery. DO NOT attempt to connect to any other supply.
INSTRuCTIoNS FoR:
SUBMERSIBLE TRANSFER PUMP 24V
MODEL No: TP9424
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATIONS
Robust and compact portable pump for use with diesel, non-aggressive chemicals and fresh or dirty water.
Suitable for re-fuelling/fluid transfer of plant, agricultural and marine equipment on site. The pump is supplied with a 3mtr outlet
hose and stainless steel nozzle plus a 4mtr battery cable with clips. Will fit through a Ø54mm aperture to allow emptying of
containers. End cap can be unscrewed for periodic cleaning of the filter.
Flow rate at hose end:......... 15 ltr/min
Voltage:................................ 24Vdc
Current:................................ 3.5amp
Pressure: ............................. 15psi/1bar
Diameter: ............................. 53.5mm
Length:................................. 145mm
Weight: ................................ 0.4 kg
Duty Cycle: .......................... 15mins
3. CONTENTS
unpack the product and check the contents.
Ensure that there is no damage. If any problem is
noted, contact your supplier immediately.
A ........ 3 metre outlet hose + stainless steel nozzle
B ........ Motor
C ........ Impeller guard
D ........ Filter
E ........ End cap
F ........ Battery clips
G ........ 4 metre battery cable
H ........ Seal cap
Original Language Version
TP9424 Issue: 1 - 22/02/10
