instructions for
trolley jack 3tonne super rocket lift
model no:
3015cXD.V2
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
9
ensure the jack is in sound condition and good working order. take action for immediate repair or replacement of damaged parts.
use genuine parts only. the use of improper parts may be dangerous and will invalidate the warranty.
9
locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials.
9
use jack on level/solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions.
9
ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PArK” if automatic).
9
ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
9
ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use.
9
Place jack under lifting points recommended by vehicle manufacturer (see vehicle hand book). ensure lifting point is stable and centred
on saddle.
▲
DanGer:
use the jack for lifting only,
not
for supporting the lifted load.
9
use suitable capacity axle stands under the vehicle before proceeding with any task.
9
ensure there are no persons or obstructions beneath the vehicle before lowering.
8
Do not
operate the jack if damaged.
8
Do not
work under the vehicle until axle stands have been correctly positioned.
8
Do not
exceed the rated capacity of the jack (3tonne/3000kg). When lifting a load of maximum capacity or close to it, it is
recommended that the effort be reduced by the use of assistance during this operation.
8
Do not
adjust the safety overload valve.
8
Do not
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
Do not
allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8
Do not
top up hydraulic system with brake fluid. use hydraulic jack oil only and use a qualified person to maintain jack hydraulic
system.
8
Do not
allow untrained persons to operate the jack.
8
Do not
use jack for purposes other than which it is designed.
8
Do not
allow persons to ride on the jack.
9
When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. specification
model no: .......................................................... 3015cXd.V2
minimum saddle height: ............................................. 132mm
maximum saddle height: ............................................ 472mm
minimum chassis height: ............................................ 158mm
length: ....................................................................... 620mm
Weight: ........................................................................... 31kg
3. asseMbly
3.1.
Assemble the two-piece handle, using the bolt provided.
3.2.
insert the handle into the socket, taking care to ensure that the square
indentation at the base of the handle fits correctly over the square
head of the central release shaft.
3.3.
secure the handle using the bolt provided (see fig.1).
do not over-tighten.
4. before use
4.1.
check the oil level.
4.1.1.
ensure the jack is resting on level ground and that the ram is fully retracted. open the release valve by turning the handle
anticlockwise.
4.1.2.
remove the cover plate by unscrewing the four screws.
4.1.3.
remove the filler plug with an 8mm hex key (see fig.1) the oil level should be level with the bottom of the hole.
4.1.4.
if necessary, top up with hydraulic oil. use only sealey hydraulic jack oil (see your authorised sealey stockist). refit filler plug.
refer to
instruction
manual
Wear safety
footwear
fig.1
3015cXd.V2 | issue:1 27/04/17
Original Language Version
© Jack sealey limited
