The SSG1X is a well balanced spray gun suitable for refinishing. Supplied with an aluminium suction feed
pot, the gun has the following specification:
Instructions for:
SUCTION FEED REFINISHING
GUN
Model:
SSG1X
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
Standard Set Up: . . . . . .1.8mm (for 1.5, 2 & 2.5mm see Parts List)
Nominal Operating Air Pressure: . . . . . . . . . .4 - 5 bar (60 - 75psi)
Nominal Air Consumption: . . . . . . . . . . . . . . . .350l/min (12.5cfm)
Pot Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1l
Air Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4"
2. SPECIFICATION
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3
Familiarise yourself with the application and limitations, as well as the potential hazards of the spray gun.
p
WARNING!
Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
3
Maintain the spray gun in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
3
Locate the spray gun in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is adequate
ventilation and lighting.
3
Keep the spray gun clean for best and safest performance.
3
Ensure the air system has sufficient output for the spray gun air consumption (see specification).
3
Wear approved respiratory protection, safety eye goggles and skin protection.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and tie back long hair.
3
Keep children and unauthorised persons away from the work area.
3
When gun is not in use ensure the air supply is disconnected.
3
Avoid unintentional operation.
7
DO NOT
paint were there is any source, or possible source, of ignition as paint mist is extremely flammable.
7
DO NOT
point spray gun at yourself or at other persons or animals.
7
DO NOT
carry the by the air hose, or yank the hose from the air supply.
7
DO NOT
use the spray gun for any purpose other than for which it is designed.
7
DO NOT
allow untrained persons to operate the spray gun.
7
DO NOT
get the spray gun wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT
operate gun if any parts are missing or damaged as this may cause failure and/or personal injury.
7
DO NOT
direct air from the air hose at yourself or others.
3
When not in use switch the spray gun off and disconnect from the air supply.
3. AIR SUPPLY
4. PREPARATION
3.1. Ensure the air valve is in the "off" position before connecting to the air supply.
3.2. You will require an air pressure of approximately 70psi and an air volume of more than 12cfm to operate the gun.
3.3.
p
WARNING!
Ensure the air supply is clean does not exceed 90psi. Too high an air pressure and unclean air will shorten the
life of the gun due to excessive wear and may be dangerous, causing damage and/or personal injury.
3.4. Drain the air supply tank daily. Water in the air line will damage the gun and contaminate the paint.
3.5. Clean the compressor air inlet filter weekly. For recommended hook-up, see diagram.
3.6. Line pressure should be increased to compensate for unusually
long air hoses (over 8 metres). The minimum hose diameter
should be 10mm I.D. and fittings must have the same
inside dimensions.
3.7. Keep hose away from heat, oil and sharp
edges. Check hoses for wear, and make
certain that all connections are secure.
The gun was treated with an anti-corrosion agent to protect it prior to first use. Before first use make sure that the gun is flushed with paint
solvent to remove the agent.
p
WARNING!
Solvents and cleaning agents based on halogenated hydrocarbons, e.g. 1.1.1-trichlorethylene and methylene chloride, may have
a chemical reaction with the aluminium components of the gun. In extreme cases the reaction can be explosive. Therefore, use only
solvents/cleaning agents which DO NOT contain these substances.
SSG1X - 0016 - (1) - 070601
