The SSG1/GX is a well balanced spray gun suitable for applying finishing coats. Supplied with a
plastic gravity feed pot the gun has the following specifications:
INSTRUCTION FOR:
GRAVITY FEED SPRAY GUN
MODEL No:
SSG1/GX
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
Standard Set up: . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4mm
Air Pressure:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-50psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . .80-225 L/min (2.82-8.94cfm)
Air Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4" BSP
2. SPECIFICATIONS
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
3
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the spray gun.
p
WARNING!
Disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
3
Paint cup remains pressurised after gun is disconnected from air line.
DO NOT pull the trigger, but depressurise by gently opening cup.
3
Maintain the
spray gun in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.
3
Locate the spray gun in an adequate working area for its function, keep area clean and tidy and free from unrelated materials, and ensure
there is adequate ventilation and lighting.
3
Keep the spray gun clean for best and safest performance.
3
Ensure the air system is suitable to the spray gun air consumption, (see specifications).
3
Wear approved respiratory protection and safety eye goggles.
3
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and tie back long hair.
3
Keep children and unauthorised persons away from the working area.
3
When not in use ensure the air supply is turned off.
3
Avoid unintentional operation.
7
DO NOT point spray gun at yourself, at other persons or animals.
7
DO NOT carry the by the air hose, or yank the hose from the air supply.
7
DO NOT use the spray gun for any purpose other than for which it is designed.
7
DO NOT allow untrained persons to operate the spray gun.
7
DO NOT get the spray gun wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate gun if any parts are missing or damaged as this may cause failure or personal injury.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use switch the spray gun off, and disconnect from the air supply.
3. AIR SUPPLY CONNECTION
3.1.
Hooking up to air supply.
Air pressure for atomization is regulated at the extractor. The amount of fluid is adjusted by the
fluid control screw on the gun
3.1.1. Ensure the spray gun air valve (or trigger) is closed before connecting to the air supply.
3.1.2. You will require an air pressure between 15-50psi, and an air flow of 80-225 L/min.
p
WARNING!
Ensure the air supply is clean and does not exceed 50 psi while operating the gun.
3.1.3. Keep hose away from heat, oil and sharp edges. Check hoses for wear, and make certain that all
connections are secure.
PIPE SIZE 1 D
(inches)
CFM 50 100 150 200
10 1/2” 3/4” 3/4”
20 3/4” 3/4” 3/4” 3/4”
30 3/4” 3/4” 1” 1”
40
1” 1” 1” 1”
50
1” 1” 1” 1”
70
1” 1” 11/4” 11/4”
Air flow Length of pipe
3.2.
Air supply from compressor unit. (fig 1).
3.2.1. The oil and water extractor should not be mounted on or near
the air compressor. The air temperature is greatly increased
during compression. As the air cools down to room
temperature (in the airline on the way to the spray gun)
the moisture in it condenses.
3.2.2. For maximum effectiveness, the oil and water extractor should
be mounted at some point in the air supply system where the
temperature of compressed air in line is likely to be at its lowest.
3.2.3. Air lines must be properly drained. Pitch all air lines back
toward the compressor so that condensed moisture
will flow back into the receiver where it can be drained off.
Each low point in the air line acts as a water trap.
Such points must be fitted with an easily accessible drain.
fig1
Original Language Version
SSG1/G Issue: 2 - 22/01/10
