background image

SM53.V3, SM54.V3 - 1 - 22/04/05

1. SAFETY INSTRUCTIONS

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions 

and properly maintained, give you years of trouble free performance.

INSTRUCTIONS FOR:

BENCH GRINDER & BUFFER

MODELS: 

SM53.V3 & SM54.V3

1.1.

ELECTRICAL SAFETY. 

p

p

 

 

WARNING! It is the user’s responsibility to read, understand and comply with the following:

You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and

all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety

devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD

(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD together with portable products that are

plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a Residual Current

Device by contacting your Sealey dealer. 

You must

also read and understand the following instructions concerning electrical safety.

1.1.1. The 

Electricity At Work Act 1989

requires all portable electrical appliances, if used on business premises, to be tested by 

a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The 

Health & Safety at Work Act 1974

makes owners of electrical appliances responsible for the safe condition of the appliance, 

and the safety of the appliance operator. 

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power 

supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, 

especially power connections, to ensure that none are loose. 

1.1.6.

Important:

Ensure the voltage marked on the product is the same as the electrical power supply

to be used, and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may require 

a fuse smaller than 13 amps for certain products, see fuse rating at right. 

1.1.7. DO NOT pull or carry the powered appliance by its power supply lead. 

1.1.8. DO NOT pull power plugs from sockets by the power cable.

1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by 

a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted. In case of damage, cut off 

and fit a new plug according to the following instructions (discard old plug safely).

(UK only - see diagram at right). 

Ensure the unit is correctly earthed via a three-pin plug. 

a)  Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to live terminal ‘L’.

c)  Connect the BLUE neutral wire to the neutral terminal ‘N’.

After wiring, check there are no bare wires, that all wires have been correctly connected and that the wire restraint is tight.

Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always marked with

this symbol      .

To re-wire, connect the brown & blue wires as indicated above. DO NOT 

connect the brown or blue to the earth terminal.

1.1.10. Some products require more than a 13 amp electrical supply. In such a case, 

NO

plug will be fitted. 

You must

contact a qualified electrician 

to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and socket with your electrician. 

1.1.11.

Cable extension reels

. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD

fitted is recommended since any product which is plugged into the reel will be protected. The section of the cores of the cable is

important and should be at least 1.5mm

2

. However, to be absolutely sure that the capacity of the reel is suitable for this product and

for others that may be used in the other output sockets, we recommend the use of 2.5mm

2

section cable.

Blue

Neutral 

Wire

Yellow & Green 

Earth Wire 

Wire 

Restraint

THIS PRODUCT MUST BE

FITTED WITH A 5 AMP FUSE

Brown

Live 

Wire

1.2 GENERAL SAFETY

p

WARNING!

Disconnect the grinder from the mains power, and ensure the grinding wheels are at a standstill before attempting to changing

accessories, servicing or performing any maintenance.

3

Maintain the grinder in good condition and check moving parts alignment regularly. 

3

Replace or repair damaged parts. 

Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.

s

s

DANGER! DO NOT use a damaged stone as it is dangerous and may cause damage or serious personal injury.

p

WARNING! Only persons qualified under the “Abrasive Wheels Regulations” and holding a current grinding wheel 

certificate are to change or dress grinding stones. Unplug grinder from mains power and refer to chapter 4 “Grinding Stones” for details.

p

WARNING!

Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts. 

A guard or any other part that is damaged should be checked to ensure that it will operate properly and perform its intended function

before tool is used. The safety guard is a mandatory fitting where grinder is used in premises covered by the Health & Safety at Work Act.

3

Locate grinder in an adequate working area for its function, keep area clean, tidy and free from unrelated materials. Ensure adequate lighting.

3

Before each use check grinding wheel for condition. If worn or damaged replace immediately.

p

WARNING! 

Always wear approved eye or face protection when operating the grinder. 

3

Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard. Wear ear defenders and gloves if necessary.

3

Keep hands and body clear of the workpiece when operating the grinder.

3

Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.

3

Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.

3

Keep children and unauthorised persons away from the working area.

7

DO NOT force the grinder to achieve a task it was not designed to perform.

7

DO NOT operate the grinder if any parts are damaged or missing as this may cause failure or possible personal injury.

p

WARNING!

DO NOT grind, or sand any materials containing asbestos.

7

DO NOT switch the grinder on whilst the wheel is in contact with the work piece.

Reviews: