background image

PARTS CLEANING TANK ExTRA dEEP 136LTR

Model no: 

SM40d.V2

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAfETy

1.1.    

ELECTRICAL SAfETy

 

‰

  

WARNING!

 It is the responsibility of the owner and the operator to read, understand and comply with the following:

 

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets    

 

and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of    

 

appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. You  

 

must also read and understand the following instructions concerning electrical safety.

 

9

   ensure that cables are always protected against short circuit and overload.

 

9

   Regularly inspect power supply cables and plugs for wear or damage and check all connections 

 

to ensure that none are loose.

 

9

   ensure that the voltage marked on the appliance matches the power supply to be 

 

used and that the plug is fitted with the correct fuse - see fuse rating at right.

 

8

  

dO NOT

 use worn or damaged cables, plugs or connectors. Have any faulty item repaired or 

 

replaced immediately by a competent electrician.

 

9

   It is recommended that this heater is wired directly to a fused isolator switch. If, however, a plug 

 

is fitted, the following applies:

 

9

   Fit a new plug according to the following instructions (UK only).

 

a) Connect the GReen/YelloW earth wire to the earth terminal ‘e’.

 

b) Connect the BRoWn live wire to the live terminal ‘l’.

 

c) Connect the BlUe neutral wire to the neutral terminal ‘n’.

 

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, 

 

    that the cable restraint is tight.

1.2. 

  GENERAL SAfETy

 

‰

  

WARNING!

 ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this  

 

 equipment.

 

9

   Familiarise yourself with the application, limitations and potential hazards of the cleaning tank.

 

‰

  

WARNING!

 disconnect the cleaning tank from the mains power before changing accessories, servicing or performing any maintenance.

 

9

   Maintain the cleaning tank in good condition (use an authorised service agent). 

 

9

   Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 

 

9

   locate the cleaning tank in a suitable work area. ensure that the tank stands on a firm level surface. Keep the area clean and tidy and  

  free from unrelated materials. ensure that the area is well ventilated and has adequate lighting.

 

9

   Keep the cleaning tank away from heat sources such as heater, sparks, open flames etc.

 

9

   ensure that there are no flammable or combustible materials near the work area.

 

8

  

dO NOT

 use the cleaning tank where there are flammable liquids, solids or gases (e.g. paint solvents).

 

9

   In case of fire in the unit, 

dO NOT

 attempt to remove parts, or move the tank. The lid is fused and will close automatically to extinguish  

  the flames.

 

9

   In case of fire in tank, 

dO NOT

 attempt to move unit or remove parts from tank. The lid is fusible and will automatically close  

 

  extinguishing fire.

 

9

   When cleaning parts ensure that nothing in the tank, including any parts basket, is in a position that would prevent the lid    

  from closing fully if and when the fusible link activates.

 

8

  

dO NOT

 use any solvent with a flash point below 140°F. We recommend you use Sealey degreasing Solvent (AK25), contact your local  

  stockist for details.

 

‰

  

WARNING! 

only to be used with water soluble cleaning agents.

 

‰

  

WARNING! 

Always wear approved eye or face protection when operating the cleaning tank. 

 

9

   Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.

 

9

   Wear appropriate protective clothing.

 

9

   Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

 

9

   Keep children and unauthorised persons away from the work area.

 

9

 

  Avoid accidental starting of the pump by ensuring the unit is unplugged from the mains power when not in use.

 

8

  

dO NOT

 use the cleaning tank for any purpose other than that for which it is designed.

 

8

  

dO NOT

 use cleaning tank in wet or damp locations or areas where there is condensation. 

 

8

  

dO NOT 

allow untrained persons to operate the cleaning tank.

SM40d.V2 Issue 2 (HF) 15/06/18

Original Language Version

© Jack Sealey limited

Refer to 

instructions

 Wear eye 

protection

 Wear protective 

gloves

Recommended fuse rating

3 Amp

Reviews: