SG14 - -250902
Instructions For:
UNDER-BODY COATING GUN
Model
:
SG14
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY,
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p
WARNING!
Disconnect the gun from the air supply before changing accessories, servicing or performing
any maintenance.
3
Maintain the gun in good condition. Replace or repair damaged parts.
Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
3
Keep the gun clean and rinse out nozzle and pipes with thinners after use.
p
p
WARNING!
If gun components become blocked there is a danger of excessive pressure building up in unit
causing the canister to burst.
3
Locate the gun in a suitable, well ventilated area, keep area clean, tidy and free from unrelated materials and
ensure there is adequate lighting.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Keep children and unauthorised persons away from the working area.
3
Avoid unintentional operation.
3
Ensure coating/wax manufacturers instructions are carefully followed.
7
DO NOT hold gun or attachments close to your face (especially eyes, ears, etc.) and do not point gun or air
hose at other persons or animals.
7
DO NOT carry by the air hose, or yank the hose or the gun from the air supply.
7
DO NOT use the gun for any purpose other than for which it is designed and do not use with any other fluid.
7
DO NOT operate the gun if damaged.
3
When not in use disconnect from the air supply and store in a safe, dry, childproof area.
2.
INTRODUCTION & SPECIFICATION
2.1. Introduction
2.1.1. The SG14 is used for anti-rust treatment of vehicles and agricultural machines by the application of underseal
compound or wax.
3.1 Air Supply
3.1.1 Ensure air valve is in "off" position before connecting to the air supply.
3.1.2. An air pressure of no more than 90psi and an air volume of 8cfm will be required.
3.1.3.
p
WARNING!
Ensure air supply does not exceed 90psi. Too high a pressure will shorten the
product life and may be dangerous, causing damage and/or personal injury.
3.1.4. Drain air supply tank daily. Water in the air line will damage the gun and will invalidate your warranty.
3.1.5. Clean air inlet filter screen weekly. For recommended hook-up, see figs.1.a,b,&c.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose and fittings diameter should be 10mm I.D.
3.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2. Couplings.
3.2.1. Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome
this, connect a leader hose to the wrench. A quick change coupling may then be used to connect the leader
hose to the air line recoil hose. See fig.1. a, b & c
.
3.
PREPARING THE GUN FOR USE
Fig 1a
Fig 1b
Fig 1c
SG14 - -250902
Instructions For:
UNDER-BODY COATING GUN
Model
:
SG14
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL
REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE
PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY,
AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p
WARNING!
Disconnect the gun from the air supply before changing accessories, servicing or performing
any maintenance.
3
Maintain the gun in good condition. Replace or repair damaged parts.
Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
3
Keep the gun clean and rinse out nozzle and pipes with thinners after use.
p
p
WARNING!
If gun components become blocked there is a danger of excessive pressure building up in unit
causing the canister to burst.
3
Locate the gun in a suitable, well ventilated area, keep area clean, tidy and free from unrelated materials and
ensure there is adequate lighting.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Keep children and unauthorised persons away from the working area.
3
Avoid unintentional operation.
3
Ensure coating/wax manufacturers instructions are carefully followed.
7
DO NOT hold gun or attachments close to your face (especially eyes, ears, etc.) and do not point gun or air
hose at other persons or animals.
7
DO NOT carry by the air hose, or yank the hose or the gun from the air supply.
7
DO NOT use the gun for any purpose other than for which it is designed and do not use with any other fluid.
7
DO NOT operate the gun if damaged.
3
When not in use disconnect from the air supply and store in a safe, dry, childproof area.
2.
INTRODUCTION & SPECIFICATION
2.1. Introduction
2.1.1. The SG14 is used for anti-rust treatment of vehicles and agricultural machines by the application of underseal
compound or wax.
3.1 Air Supply
3.1.1 Ensure air valve is in "off" position before connecting to the air supply.
3.1.2. An air pressure of no more than 90psi and an air volume of 8cfm will be required.
3.1.3.
p
WARNING!
Ensure air supply does not exceed 90psi. Too high a pressure will shorten the
product life and may be dangerous, causing damage and/or personal injury.
3.1.4. Drain air supply tank daily. Water in the air line will damage the gun and will invalidate your warranty.
3.1.5. Clean air inlet filter screen weekly. For recommended hook-up, see figs.1.a,b,&c.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The
minimum hose and fittings diameter should be 10mm I.D.
3.1.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all
connections are secure.
3.2. Couplings.
3.2.1. Vibration may cause failure if a quick change coupling is connected directly to the wrench. To overcome
this, connect a leader hose to the wrench. A quick change coupling may then be used to connect the leader
hose to the air line recoil hose. See fig.1. a, b & c
.
3.
PREPARING THE GUN FOR USE
Fig 1a
Fig 1b
Fig 1c
