2.
CONTENT & SPECIFICATIONS
p
p
WARNING!
Ensure that the grinder is unplugged from the power supply before assembly.
3.1.
Fitting the grinding/cutting disc
3.1.1. Place the disc receiver (fig. 2.3) over the centre spindle with the key lugs facing
down (fig. 2a) to engage with the flats on the shaft.
3.1.2. Place grinding disc (fig. 2.4) on the spindle with the printed side towards the head of
the grinder.
3.1.3. Stop the spindle from turning by pushing in and holding the stop button (fig. 4.B).
3.1.4. Lock grinding disc into place by tightening the locking nut (fig. 2.5) with the pin wrench (fig. 3).
DO NOT over tighten. Fit the locking nut with the spigot engaged in the grinding disc bore.
3.1.5. Release the locking button (fig. 4.B) and check that it springs back to the initial position.
3.2.
Fitting the sanding backing disc (SG101 only)
3.2.1. Fit the disc receiver (fig. 2.3) as in 3.1.1.
3.2.2. Place the backing disc (fig. 2.8) on the spindle, concave side facing out.
3.2.3. Stop the spindle from turning by pushing in and holding stop button (fig. 4.B).
3.2.4. Lock sanding disc in place by tightening the lock nut (fig. 2.7) with the pin wrench (fig. 3).
DO NOT over tighten.
3.2.5. Release the locking button (fig. 4.B) and check that it springs back to the initial position.
3.3.
Side handle
3.3.1. The side handle must be used for complete control and safety.
3.3.2. Screw the handle (fig. 1.2) into the left- or right-hand mounting, as required.
3.4.
Positioning, removing and refitting the guard
3.4.1. The guard (fig. 5.C) may be positioned at any angle to suit the task. Position the guard to allow the best access to the workpiece whilst
providing maximum personal protection for the operator.
3.4.2. Loosen locking screw (fig. 5.D) and turn the guard to the required position. Lock the guard in place by re-tightening the locking screw.
3.4.3. The guard can be removed for sanding tasks, as follows (SG101 only):
1) Remove locking screw (fig. 5.D) and the three retaining screws (fig. 5.E).
2) Refitting the guard is the reverse of 3.4.3.
ALWAYS REATTACH THE GUARD FOR GRINDING/CUTTING.
3.
ASSEMBLY & ADJUSTMENT
Remove items from packing and identify parts against fig. 1. If any part is damaged or missing contact your supplier immediately.
SPECIFICATION - SG101
Power input . . . . . . . . . . . . . . . . . . . 720 watt
No-load speed . . . . . . . . . . . . . . . 10,000rpm
Spindle size. . . . . . . . . . . . . . . . . . M10X1.25
Sanding disc max. diam. . . . . . . . . . . 100mm
Grinding/Cutting disc max. diam. . . . . 100mm
Disc bore . . . . . . . . . . . . . . . . . . (5/8) 16mm
Overall length . . . . . . . . . . . . . . . . . . 280mm
Sound pressure level . . . . . . . . . . . 90.9dB(A)
Sound power level . . . . . . . . . . . . 103.9dB(A)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . 2.3kg
fig. 3
fig. 2
CONTENT LIST
1.
Angle Grinder
2.
Side Handle
3.
Disc Receiver
4
Grinding Disc
5.
Locking Nut
6
Spanner
7.
Backing Disc Lock Nut (SG101 only)
8.
Backing Disc (SG101 only)
fig. 5
4.
GRINDING/CUTTING DISCS
fig. 2a
fig. 4
p
WARNING!
DO NOT USE DISCS THAT ARE DAMAGED, OR SUSPECTED TO BE DAMAGED.
4.1. Before using a grinding/cutting disc ensure that there are no fissures or cracks. Once mounted on the grinder, test the disc before
use by facing the grinder in a safe direction (point away from yourself, others and vulnerable items) and run for a short time.
s
s
DANGER! Use of damaged discs is dangerous and may cause personal injury.
4.2. Grinding and cutting discs used in association with this machine shall be of an adequate speed rating and be suitable for the job
in hand. The discs shall be made in accordance with British Standard 4481:Part 1 1989. Only persons holding a grinding
wheel certificate are authorised to change grinding discs. Ensure that the speed rating on the disc is equal to, or higher than, that of the grinder.
fig. 1
SPECIFICATION - SG115
Power input . . . . . . . . . . . . . . . . . . . 720 watt
No-load speed . . . . . . . . . . . . . . . 10,000rpm
Spindle size. . . . . . . . . . . . . . . . . . . M14X2.0
Grinding/Cutting disc max. diam. . . . . 115mm
Disc bore. . . . . . . . . . . . . . . . (7/8) 22.23mm
Overall length . . . . . . . . . . . . . . . . . . 280mm
Sound pressure level . . . . . . . . . . . 90.9dB(A)
Sound power level . . . . . . . . . . . . 103.9dB(A)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . 2.3kg
SG101 & SG115 - 2 - 080503
