instructions for
suction feed spray gun
1.7, 2.0, 2.5mm set up
model no:
sg1.7s, 2.0s, 2.5s
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
9
familiarise yourself with the application and limitations, as well as the potential hazards of the spray gun.
Warning!
disconnect the spray gun from the air supply before changing accessories, servicing or performing any maintenance.
9
maintain the
spray gun in good condition (use an authorised service agent).
9
replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
9
locate the spray gun in a suitable work area, keep area clean and tidy and free from unrelated materials, and ensure that there is
adequate ventilation and lighting.
9
Keep the spray gun clean for best and safest performance.
9
ensure the air system has sufficient output for the spray gun air consumption (see specification).
9
Wear approved respiratory protection, eye protection and skin protection.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
When gun is not in use ensure the air supply is disconnected.
9
Avoid unintentional operation.
8
do not
paint were there is any source, or possible source, of ignition as paint mist is extremely flammable.
8
do not
point spray gun at yourself or at other persons or animals.
8
do not
carry the by the air hose, or yank the hose from the air supply.
8
do not
use the spray gun for any purpose other than for which it is designed.
8
do not
allow untrained persons to operate the spray gun.
8
do not
get the spray gun wet or use in damp or wet locations or areas where there is condensation.
8
do not
operate gun if any parts are missing or damaged as this may cause failure and/or personal injury.
8
do not
direct air from the air hose at yourself or others.
2. introduction
ideal for applying undercoat, adhesives and primers. features adjustable paint flow and fan width controls. supplied with aluminium screw type
suction feed pot. suitable for use with water based paints. Alternative set-ups available separately.
3. specification
4. air supply
4.1.
for recommended hook-up, see fig.1. ensure the air valve is in the “off” position before connecting to the air supply.
4.2.
You will require an air supply capable of providing a pressure 60psi and an air volume of 11cfm to operate the gun.
Warning!
Ensure the air supply is clean and is regulated to a maximum of 60psi. Too high an air pressure and unclean
air will shorten the life of the gun due
to excessive wear and may be dangerous, causing damage and/or personal injury.
4.3.
drain the air supply tank and pressure regulator daily. Water in the air line will damage the gun and contaminate the paint.
4.4.
clean the compressor air inlet filter weekly.
4.5.
line pressure should be increased to compensate for unusually long air hoses (over 8 metres). the minimum hose diameter should be
10mm (3/8”) i.d. and fittings must have the same inside dimensions.
4.6.
Keep hose away from heat, oil and sharp edges. check hoses for wear, and make certain that all connections are secure.
refer to
instruction
manual
Wear eye
protection
Wear
respiratory
protection
Wear
protective
clothing
sG1.7s, sG2.0s, sG2.5s | issue 1 18/05/18
Original Language Version
© Jack sealey limited
model no.
sg1.7s
sg2.0s
sg2.5s
Available set ups
2, 2.5mm
1.7, 2.5mm
1.7, 2.0mm
Air pressure
57psi
57psi
57psi
Air consumption
3-4cfm
3-4cfm
3-4cfm
Pot capacity
1000ml
1000ml
1000ml
fig.1
