Instructions for:
FOLDING WORKSHOP CRANE
Model No:
SC10
SC10 - 0016 - (1) - 161100
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
3. ASSEMBLY INSTRUCTIONS
Unpack the product and check contents against the parts list in these instructions. Should there be any damaged or missing parts contact your
supplier immediately. Assemble the crane as follows:
3.1.
Lay out all the parts in the appropriate positions ready for assembly.
3.2.
When assembling, ensure that you fit a plain washer, then a locking washer before fitting nuts onto bolts.
3.3.
Assemble the crane main frame first, leaving the hydraulic ram assembly until last.
Note: At this stage all nuts and bolts should be finger tight only.
3.4.
Connect the base of the ram assembly to the ram assembly mounting.
3.5.
Raise the lift arm and carefully move it until the ram fits the arm bracket. Engage the pin and secure with the fasteners provided.
3.6.
Now tighten all the nuts and bolts on the main frame.
3.7.
Carefully lay crane on its back on the floor the assembled main frame with the ram side facing up.
3.8.
Assemble and insert the legs and locate with pins provided.
3.9.
By using the handle, push the assembled crane into the working position so that all four wheels are in contact with the floor.
3.10.
Before using crane place the pumping handle on the release valve and turn to the left. With the handle inserted in the pump socket,
pump 10-15 times through the full stroke, thus bleeding, from the hydraulic system, any air which may have entered during transit.
2. SPECIFICATION
JIB POSITION:
1
2
3
4
Product Weight
Lifting Capacity (kg)
1000
750
500
250
80kg
Jib Extension Length (mm)
850
980
1070
1160
1. SAFETY INSTRUCTIONS
Keep crane, lifting slings, support and beams in good working order and condition. Follow the inspection requirements as described
in Section 5.
Take immediate action to repair or replace damaged parts by contacting your supplier. Ensure that all accessory lifting
devices are suitably certified. If crane is damaged, remove from service immediately .
Ensure the surface on which the crane is used is level, firm and capable of supporting the weight of the crane with maximum load. Never
use the crane on tarmacadam or other soft surfaces.
Ensure the crane legs and arms are locked before use.
Keep children and unauthorised persons away from the working area.
Keep working area clean and tidy, free from unrelated materials and ensure that there is adequate lighting.
Ensure that load does not exceed the maximum lifting capacity of the crane. Overloading the crane is dangerous. Where appropriate, use
only the lifting points recommended by the manufacturer of the item to be lifted, i.e. vehicle engine.
Before lifting the load ensure that the crane jib is in the lowest practical position, that there are no obstacles which may snag the load
whilst it is being lifted and that the area above the jib is clear.
To avoid injury, be fully aware of your own and other persons locations in relation to the lifting, and lowering, of the load.
Keep a sound footing and balance, and ensure the floor is not slippery.
Ensure jib extension locking bolt and nut are in position before lifting.
Ensure the centre of gravity always remains inside the crane base.
DO NOT
harness the load at an angle.
DO NOT
allow the load to swing during lifting.
DO NOT
allow the load to drop suddenly. Lower load with care, ensuring that you are fully aware of the condition of the surface onto which
the load is to be placed.
DO NOT
operate the hydraulic power unit beyond its maximum stroke as indicated on the label.
DO NOT
load crane beyond its rated capacity for each specified jib extension position as indicated in Section 2. The capacity of the crane
reduces as the jib is extended.
DO NOT
position any part of your body beneath the load.
DO NOT
use the crane to move, or transport, a load around the workshop. The crane is a lifting device only.
DO NOT
apply any sideways pressure to any part of the crane during lifting or when a load is suspended.
DO NOT
attempt to adjust the safety valve, which has been set and sealed by the manufacturer.
DO NOT
use this product to perform a task for which it is not designed.
DO NOT
use whilst under the influence of drugs, alcohol or intoxicating medication.
DO NOT
climb on the crane.
When not in use fold the crane down and store in a safe, dry, childproof area.
WARNING! Failure to heed safety and warning instructions may result in damage and/or personal injury and will invalidate the warranty.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
