shot blasting cabinet double access
960 x 720 x 1500mm
model no:
sb974.V5
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFetY
i
1.1.
electRical saFetY
ONLY USE THE SUPPLIED TRANSFORMER PLUG FOR CONNECTING UNIT TO THE MAIN ELECTRICAL POWER SUPPLY.
WaRning!
It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current
Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCd (Residual Current device) is
used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.1.1.
The
Electricity At Work Act 1989
requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2.
The
Health & Safety at Work Act 1974
makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3.
You must ensuRe that You:
9
Inspect the transformer plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply. If worn or damaged
do not
use but immediately replace, or contact a qualified electrician.
9
Check cables are always protected against short circuit and overload.
9
Important: Check that the voltage marked on the transformer plug is the same as the power supply to be used.
9
Uncoil the cable between the transformer and the cabinet.
8
do not
pull transformer lead, or pull the transformer plug from the mains socket by the lead.
8
do not
use any other type of transformer with this product.
8
do not
place the power connector into any area of the cabinet other than the correct inlet socket.
8
do not
try to open or dis-assemble the transformer plug.
8
do not
use the transformer plug to power any other electrical item.
8
do not
get the transformer wet, or use in wet, damp conditions (for indoor use only).
WaRning! neVeR
substitute a standard 13 Amp 3 pin plug, or any other type of plug, for the transformer plug.
cable extension Reels.
When a cable extension reel is used it should be fully unwound before connection. A cable reel with an
RCd fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable
reel is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the cable reel is suitable for this product and
for others that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
1.2.
geneRal saFetY
WaRning!
ensure Health & Safety, government and local authority regulations relating to the the use of shot blasting are adhered to
when using this equipment. Familiarise yourself with the applications, limitations and potential hazards peculiar to the cabinet.
WaRning!
disconnect cabinet from mains power and air supply before changing accessories, servicing or performing any maintenance.
9
maintain the
cabinet in good condition. Replace or repair damaged parts.
Use genuine parts
only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
locate cabinet in a suitable work area, keep area clean, tidy and free from unrelated
materials. ensure adequate lighting.
▲
imPoRtant.
Use only dry abrasives such as glass bead. We recommend Sealey item
B5KG. never use fluids or mix fluids with another media in unit.
WaRning!
Always wear approved eye or face and ear protection when operating the
cabinet.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and
contain and/or tie back long hair.
9
Keep the side doors closed and secured when in use.
WaRning!
ensure correct air pressure is maintained and not exceeded. Always
keep blast nozzle directed at the workpiece.
do not
aim blast at gloves, glove
fingers or internal light. never use outside the unit. Regularly check that the exhaust vent at
the back of the cabinet is clear and that there is space between it and any wall.
9
maintain correct balance and footing. ensure the floor is clean and free from blasting grit
spillage. Wear non-slip shoes.
9
Keep children and non-essential persons away from the work area.
8
do not
use the cabinet to achieve a task it is not designed to perform.
SB974.V5 Issue 3 19/08/19
Original Language Version
© Jack Sealey limited
Transformer Plug
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
Wear a mask
