Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
Follow all workshop Health & Safety rules, regulations and conditions when using tool.
WARNING!
Disconnect from air supply before changing grinding bit or servicing.
Maintain die grinder in good condition and replace any damaged or worn parts.
Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommended 90psi.
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that
all connections are secure.
WARNING!
Before each use check grinding bit is secure, and the bit is not worn or damaged. If damaged,
replace immediately.
Ensure replacement grinding bits are not damaged (cracks, deformations or splinters etc).
Always use the correct grinding bit suitable for the material being ground. Ensure the maximum speed
specification of the bit is higher than that indicated on the machine data plate.
WARNING!
Always wear approved eye or face protection when operating the die grinder.
Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard.
Wear ear defenders and gloves if necessary.
Keep hands and body clear of the workpiece when operating the die grinder.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Secure unstable workpiece with a clamp, vice or other adequate holding device.
Keep children and non-essential persons away from the working area.
Avoid subjecting grinding bit to excessive strain, always ease grinding bit against workpiece (a harsh impact
may break the bit). Maintain a controlled progression.
Wear suitable clothing to avoid snagging.
DO NOT
wear loose jewellery and tie back long hair.
DO NOT
get the die grinder wet or use in damp or wet locations.
DO NOT
hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
DO NOT
use the die grinder for a task it is not designed to perform.
DO NOT
use cutting off wheels or router cutting wheels in the die grinder.
WARNING! DO NOT
use die grinder if damaged or faulty. Contact your local service agent.
DO NOT
use die grinder unless you have been instructed in its use by a qualified person.
DO NOT
carry the die grinder by the air hose, or yank the hose from the air supply.
DO NOT
direct air from the air hose at yourself or others.
WARNING!
DO NOT
grind any materials containing asbestos.
WARNING!
The die grinder will continue to run for a short period after the trigger is released.
DO NOT
turn the die grinder on whilst the grinding bit is in contact with the workpiece.
DO NOT
use die grinder where there are flammable liquids, solids or gases such as paint solvents, including
waste wiping or cleaning rags etc. as generated sparks may be dangerous.
DO NOT
touch the workpiece close to the ground surface as it will be very hot. Allow to cool. The workpiece
may also be very sharp.
DO NOT
operate die grinder if you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use disconnect from air supply and store in a safe, dry, childproof location.
DANGER OF FIRE/ExPLOSION HAzARD
WARNING! The grinding process can produce streams of sparks (especially when grinding ferrous metals) which are a potential
source of ignition.
DO NOT use the grinder where there are flammable liquids, solids or gases.
DO NOT allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. Fabrics
contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
preference to man-made fibres.
Original Language Version
SA655 Issue: 1 - 06/09/11
INSTRUCTIONS FOR:
AIR DIE GRINDER MAxI SIzE
90° PREMIER
MODEL No:
SA655
