background image

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE

WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.

SAFETY INSTRUCTIONS

3

Follow all workshop health & safety rules, regulations, and conditions when using screwdriver. 

p

WARNING!

Disconnect from air supply before changing accessories or servicing.

3

Maintain screwdriver in good condition and replace any damaged or worn parts. 

Use

genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.

p

WARNING!

Check correct air pressure is maintained and not exceeded. We recommend 90psi.

3

Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each 

use and ensure that all connections are secure.

3

Wear approved safety eye and ear protection. 

3

Keep screwdriver bits clean and in good condition for best and safest performance. 

3

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

3

Secure non stable work piece with a clamp, vice or other adequate holding device. 

3

Ensure the screwdriver bit is secure in the chuck.

3

Avoid unintentional starting.

3

Keep children and unauthorised persons away from the working area.

8

DO NOT get the 

screwdriver

wet or use in damp or wet locations.

8

DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece. 

7

DO NOT use the screwdriver for a task it is not designed to perform. 

p

WARNING! DO NOT

use screwdriver if damaged or faulty. Contact your local service agent).

7

DO NOT use screwdriver unless you have been instructed in its use by a qualified person.

7

DO NOT drop, throw or abuse the screwdriver.

7

DO NOT carry the screwdriver by the air hose, or yank the hose from the air supply.

7

DO NOT operate screwdriver if you are tired, under the influence of alcohol, drugs or intoxicating medication.

7

DO NOT carry screwdriver with your hand on the power trigger in order to avoid unintentional starting.

7

DO NOT direct air from the air hose at yourself or others.

3

When not in use disconnect from air supply and store in a safe, dry, childproof location.

SA624 - 0016 - (2) -130700

INSTRUCTIONS FOR

AIR PISTOL SCREWDRIVER

Model:  

SA624

01284 757500

E-mail:

[email protected]

01284 703534

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component

parts without prior notice. 

IMPORTANT: 

No liability is accepted for incorrect use of this equipment. 

WARRANTY: 

Guarantee is 12

months from purchase date. proof of which will be required for any claim. 

INFORMATION: 

Call us for a copy of our latest catalogue

and promotions on 01284 757525 and leave your full name and address including your postcode.

Sole UK Distributor, Sealey Group

, Bury St. Edmunds, Suffolk.

2.

INTRODUCTION & SPECIFICATIONS

Chuck size  . . . . . . . . . . . . .1/4” - 6mm

Free speed  . . . . . . . . . . . . . . .720rpm

Torque range  . . . . . . . . . . .45-145In/lb

Air consumption  . . . . . . . . . . . . . 4cfm

Operating pressure  . . . . . . . . . . .90psi

Air inlet size  . . . . . . . . . . . . . 1/4” BSP

Weight  . . . . . . . . . . . . . . . . . . . .1.4kg

Fully polished finish with exhaust through handle base for reduced noise emission. Smooth air motor

runs on high quality ball bearings for long life and reliability. Fully reversible drive with  finger-tip

control set above trigger. Fully adjustable torque between 45 and 145 ins/lb. Accepts 6mm hex

driver bits. Rubber grip gives added control.

Item Part No 

Description

Item Part No 

Description

Original Date:

010700

Issue Date:

010700 

Version No:

Date Modified:

N/A 

1 SA624/01 MOTOR HOUSING    

2 SA624/02 SPRING PIN     

3 SA624/03 DAMPING MATERIAL   

4 SA624/04 EXHAUST DIFFUSER  

5 SA624/05 AIR INLET  

6 SA624/06  SCREW         

7 SA624/07 RUBBER GRIP   

8 SA624/08 MOTOR GASKET   

9 SA624/09  BALL BEARING  

10 SA624/10 END PLATE  

11 SA624/11  SPRING PIN 

12 SA624/12 CYLINDER  

13 SA624/13 ROTOR BLADE  

14 SA624/14 ROTOR    

15 SA624/15 O-RING   

16 SA624/16 REVERSE BUSHING   

17 SA624/17  O-RING  

18 SA624/18 REVERSE RETAINER  

19 SA624/19 REVERSE LEVER 

20 SA624/20 VALVE STEM SET  

21 SA624/21 VALVE SPRING  

22 SA624/22 SET SCREW 

23 SA624/23 TRIGGER  

24 SA624/24 SPACER 

25 SA624/25  PINION GEAR   

26 SA624/26 PLANET GEAR   

27 SA624/27  BUSHING  

28 SA624/28 PIN   

29 SA624/29  REDUCTION SPINDLE   

30 SA624/30  CENTRE GEAR    

31 SA624/31  WORK SPINDLE    

32 SA624/32  SPRING  

33 SA624/33  SPRING GUIDE  

34 SA624/34 INTERNAL GEAR  

35 SA624/35 BALL BEARING   

36 SA624/36 CLAMP NUT  

37 SA624/37  DRIVE DOG  

38 SA624/38  RETAINING RING   

39 SA624/39 RETAINING RING  

40 SA624/40  CAM SPINDLE  

41 SA624/41 STEEL BALL  

42 SA624/42 CLUTCH CARRIER  

43 SA624/43  STEEL BALL   

44 SA624/44  WASHER 

45 SA624/45 SPRING   

46 SA624/46 WASHER  

47 SA624/47 ADJUST NUT   

48 SA624/48 SPACER  

49 SA624/49 CLUTCH HOUSING   

50 SA624/50 BALL RETAINER  

51 SA624/51 SPRING     

52 SA624/52  WASHER    

Reviews: