![background image](http://html.mh-extra.com/html/sealey/sa52/sa52_instructions_1227181001.webp)
AIR NEEDLE SCALER/FLUX CHIPPER
MODEL NO:
SA52
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
WARNING!
Disconnect from air supply before changing accessories or servicing.
9
Maintain the needle scaler in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
WARNING!
Check correct air pressure is maintained and not exceeded. We recommend 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
9
Only use needles which are specifically designed for use with a needle scaler.
9
Wear approved safety eye/face shield, ear defenders, and hand protection.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non-essential persons away from the working area.
8
DO NOT
use the needle scaler for a task it is not designed to perform.
WARNING!
DO NOT
use needle scaler if damaged or thought to be faulty. (Contact Sealey service agent).
8
DO NOT
use needle scaler unless you have been instructed in its use by a qualified person.
8
DO NOT
carry the needle scaler by the air hose, or yank the hose from the air supply.
8
DO NOT
operate needle scaler if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
carry needle scaler with your hand on the power trigger in order to avoid unintentional starting.
8
DO NOT
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Straight type air hammer supplied with interchangeable needle and chisel heads. Suitable for cleaning heavy paint and rust scale from metal
surfaces. Palm control trigger mechanism. Replacement needle set and chisel available.
3. SPECIFICATION
Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32mm
Free speed: . . . . . . . . . . . . . . . . . . . . . . 4800bpm
Air consumption:. . . . . . . . . . . . . . . . . . . . . . . 3cfm
Operating pressure: . . . . . . . . . . . . . . . . . . . 90psi
Air inlet size:. . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Noise Power: . . . . . . . . . . . . . . . . . . . . . 105dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . 94dB(A)
Vibration Emission Value:. . . . . . . . . . . . . 8.56m/s²
Uncertainty Emission Value:. . . . . . . . . . . 1.34m/s²
Replacement Needle Set (12pc): . . . . . . . SA51/16
Replacement Chisel: . . . . . . . . . . . . . . . . SA52/15
4. PREPARATION
4.1.
AIR SUPPLY
4.1.1.
Ensure tool valve (or trigger) is in the “off” position before connecting to the air supply.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to specification.
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too high an air pressure and unclean air
will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
4.1.3.
Drain the air tank daily. Water in the air line will damage the tool.
4.1.4.
Clean air inlet filter weekly. Recommended hook-up procedure is shown in fig.1.
4.1.5.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose diameter should be
1/4” I.D. and fittings must have the same inside dimensions.
4.1.6.
Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
SA52 Issue 3 (H,F) 24/01/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear protective
clothing
Wear a mask