PROFESSIONAL AIR LINE GAUGE
MODEL NO’S:
SA37/93.V4, SA37/93B, SA37/94.V3,
SA37/95, SA37/98, SA37/99
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Disconnect the tyre inflator from the air supply before changing accessories, servicing or performing any maintenance.
9
Keep children and unauthorised persons away from the work area.
9
Keep the gauge screen and tyre inflator clean.
9
Replace damaged parts with genuine Sealey parts. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Check tyre pressures when they are cold.
8
DO NOT
direct the tyre inflator outlet at yourself or others including animals.
8
DO NOT
carry the tyre inflator by the hose, or tug the hose from the air supply.
8
DO NOT
use the tyre inflator for a task which it is not designed to perform.
8
DO NOT
operate the tyre inflator when you are tired or under the influence of intoxicating medicines, drugs or alcohol.
8
DO NOT
operate the tyre infltor if parts are missing or damaged, this could be dangerous.
8
DO NOT
drop or bump the tyre inflator.
8
DO NOT
get the tyre inflator wet.
8
DO NOT
operate near appliances with strong magnetic fields, corrosive gasses or corrosive liquids.
2. INTRODUCTION
Models SA37/93, SA37/93B, SA37/94 and SA37/95
manufactured to comply with EN 12645. Aluminium body with rubber bumper.
Linear pressure scale, dual calibrated in psi and bar, with parallax correction.
Models SA37/93 and SA37/93B
have a 0.5m flexible hose fitted with 240mm twin push-on air connector. Model SA37/94
is fitted with a 2.5m hose with clip-on air connector for compliance with safety regulations relating to inflation of commercial and
agricultural vehicle tyres. All are supplied with a serial numbered calibration certificate.
Warranty for SA37/93, SA37/94 and SA37/95 is two years and warranty for SA37/93B is three years.
Model SA37/95:
Die cast aluminium body with large rubber bumper. Linear pressure scale, dual calibrated in psi and bar, with
parallax correction. 2.5m Flexible hose fitted with twin lock-on air connector. Supplied with a serial numbered calibration certificate
Models SA37/98 and SA37/99
manufactured from nylon polymer and robust glass. Ergonomic lightweight design with textured
thumb lever. Increased window size ensures clearer vision and better accuracy. Linear pressure scale, dual calibrated in
psi and bar. 255mm Flexible hose with a clip-on air connector fitted to SA37/98. 205mm Flexible hose with 250mm twin hold-on air
connector fitted to SA37/99. 1 Year guarantee*.
3. SPECIFICATION
M
odels: SA37/93, SA37/93B, SA37/94 and SA37/95
P
ressure range: ...................................0 - 9.6bar (0 - 140psi)
P
ressure units: ........................................................... bar, psI
Air supply minimum: ......................................... 5.5bar (80psi)
Air supply maximum: ....................................... 15bar (218psi)
Inlet size: ..................................................................1/4” BSP
M
odels: SA37/98 and SA37/99
P
ressure range: ...................................0 - 9.6bar (0 - 140psi)
P
ressure units: ........................................................... bar, psI
Air supply minimum: ......................................... 5.5bar (80psi)
Air supply maximum: ....................................... 13bar (188psi)
Inlet size: ..................................................................1/4” BSP
4. OPERATION
4.1.
TO READ PRESSURE
4.1.1.
Place hold-on chuck squarely and firmly onto tyre valve, before each pressure reading fully depress lever and release.
4.2.
TO INFLATE
4.2.1.
Place hold-on chuck squarely and firmly onto the valve. Fully depress lever for an appropriate period then release lever to display
pressure. Check pressure gauge and repeat procedure until correct pressure level is achieved.
S
A37/93.V4, SA37/93B, SA37/94.V3, SA37/95, SA37/98, SA37/99 Issue 2 15/06/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions
