reciprocating air saw slim body
model no:
sa348
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
warning!
ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
warning!
disconnect from air supply before changing the blade or file, servicing or performing maintenance.
9
maintain the tool in good condition.
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable, clean and tidy work area, free from unrelated materials. ensure that there is adequate lighting.
warning!
Always wear approved eye or face and hand protection when operating the saw.
9
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from work area.
8
do not
use blades that are cracked or deformed.
8
do not
use hacksaw blade segments.
9
ensure that blades and files are clamped tightly to the airtool.
9
Check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the saw. never hold a workpiece by hand. Use a vice or clamps.
warning!
ensure correct air pressure is maintained and not exceeded. Recommended pressure is 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Prolonged exposure to vibration from this tool poses a health risk. It is the employer’s/owner’s responsibility to correctly assess the
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
8
do not
use any power source except an air compressor.
8
do not
operate the tool near any inflammable
substance or on any container that has held an inflammable substance.
8
do not
use tool for a task it is not designed to perform.
8
do not
operate tool if any parts are damaged or missing as this may cause failure and/or personal injury.
8
do not
carry the tool by the hose, or yank the hose from the air supply.
8
do not
operate tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not
carry the tool with your finger on the trigger.
8
do not
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. introduction
Suitable for a variety of bodyshop applications such as cutting through panels, sills and chassis members. excellent for initial crash-
repair preparation when quick removal of damaged panels is required. Fitted with safety trigger device. Supplied with a starter pack of
blades.
3. specification
model no.:.................................................................. sa348
Free Speed: ............................................................ 9000bpm
Stroke: ......................................................................... 10mm
maximum Cutting Capacity: ............. 2mm Steel, 3mm Aluminium
Air Consumption: ........................................................... 3cfm
operating Pressure: ...................................................... 90psi
Air Inlet Size: .............................................................1/4”BSP
Weight: ...................................................................... 0.425kg
noise Power:.............................................................99dB(A)
noise Pressure: ........................................................88dB(A)
Vibration/Uncertainty .......................................11.985/1.5m/s
2
consumables:
14 TPI Air Saw Blade ............................................. SA34/B14
24 TPI Air Saw Blade ............................................. SA34/B24
32 TPI Air Saw Blade ............................................. SA34/B32
Original Language Version
© Jack Sealey limited
Refer to
instruction
manual
Wear protective
gloves
Wear eye
protection
Wear ear
protection
SA348 Issue 1 12/02/19
