RECIPROCATING AIR SAW
MODEL NO:
SA342
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
WARNING!
Disconnect from air supply before changing the blade, servicing or performing maintenance.
9
Maintain the
saw in good condition (use an authorised service agent).
9
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable clean and tidy work area, free from unrelated materials, Ensure that there is adequate lighting.
WARNING!
Always wear approved eye or face and hand protection when operating the saw.
9
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
Ensure workpiece is secure before operating the saw.
9
Never hold a workpiece by hand. Use a vice or clamps.
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
NOTE:
Prolonged exposure to vibration from this saw poses a health risk. It is the employer’s/owner’s responsibility to assess
the hazard correctly and issue guidelines for safe periods of use and offer suitable protective equipment.
8
DO NOT
use any power source except an air compressor.
8
DO NOT
operate saw near any flammable substance or on any container that has held a flammable substance.
8
DO NOT
use the saw for a task it is not designed to perform.
8
DO NOT
operate saw if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT
carry the saw by the hose, or pull the hose from the air supply.
8
DO NOT
operate saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
carry the saw with your finger on the trigger.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Ideal for a variety of bodyshop applications such as cutting panels, exhaust work, sills and chassis members. Fitted with safety trigger device
to prevent accidental operation. Features adjustable blade guide. Supplied with a starter pack of blades.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SA342
Maximum Cutting Capacity: . . . . . .1.5mm (Steel & Aluminium)
Free Speed: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9000spm
Operating Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90psi
Air Consumption: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4cfm
Air Inlet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Stroke: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mm
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.166m/s²
Uncertainty: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5m/s
²
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99dB(A)
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88dB(A)
Consumables: SA34/B14 - 14tpi Air Saw Blade (x5), SA34/B24 - 24tpi Air Saw Blade (x5), SA34/B32 - 32tpi Air Saw Blade (x5)
4. AIR SUPPLY
Recommended hook-up procedure is shown below.
4.1.
The saw requires an air pressure of between 50-90psi and an air flow of 4cfm.
WARNING!
Ensure the air supply is clean and does not exceed 90psi.
Too high an air pressure and/or unclean air will result in excessive wear and may be dangerous, causing damage and/or personal injury.
SA342 Issue 3 (F,3) 05/08/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
