AIR RIVETER 1/4” STEEL ALUMINIUM, ALLOY
& STAINLESS STEEL RIVETS
MODEL NO:
SA314.V4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the riveter.
WARNING!
Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
9
Maintain the
riveter in good condition (use an authorised service agent).
9
Replace or repair damaged parts.
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Keep the riveter clean for best and safest performance.
WARNING!
Always wear approved eye (or face) and hand protection when operating the riveter.
9
Maintain correct balance and footing.
DO NOT
over reach, ensure the floor is not slippery, wear non slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear or working parts.
9
Keep the riveter away from your body and at a safe distance from others.
9
Keep children and unauthorised persons away from the working area.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Ensure that spent rivet stems are disposed of correctly and
DO NOT
cause a hazard.
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use, and ensure that all connections are
secure.
8
DO NOT
use the riveter for a task it is not designed to perform.
8
DO NOT
operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
9
Ensure the safety cap is correctly fitted.
8
DO NOT
carry the by the hose, or yank the hose from the air supply.
8
DO NOT
get the riveter wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
allow untrained persons to operate the riveter.
8
DO NOT
operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
direct air from the air hose at yourself or others.
9
When not in use disconnect from the air supply and store in a safe, dry, child proof location.
9
Avoid unintentional starting.
2. INTRODUCTION
i
Suitable for aluminium, steel and stainless steel up to 3/16”. Supplied with four riveting nozzles and two spanners. Trigger operated riveter with
hardened jaw assembly and rivet shaft safety cap. Will handle heavy assembly work.
3. SPECIFICATION
Model no: .................................................................... SA314
Nozzle sizes:
.............................. 3/32” (2.4mm), 1/8” 3.2mm, 5/32” (4mm),
.................................................. 3/16” (4.8mm), 1/4” (6.4mm)
Air consumption: ....................................................... 3.46cfm
Operating pressure: ...................................................... 90psi
Air inlet size:..............................................................1/4”BSP
Weight: .......................................................................... 1.6kg
Blind rivet type: ....................aluminium, steel, stainless steel
Noise power/pressure: ......................................... 81/70dB(A)
Vibration: .................................................................. 10.9m/s²
Uncertainty: .............................................................. 4.36m/s²
SA314.V4 Issue: 2(H,F) 01/06/18
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Wear eye
protection
Wear ear
protection
Wear protective
gloves
All manuals and user guides at all-guides.com
