AIR NIBBLER
MODEL NO:
SA28.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
WARNING!
Disconnect from air supply before changing the punch and die, servicing or performing maintenance.
9
Maintain the nibbler in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
WARNING!
Always wear approved eye or face and hand protection when operating the nibbler.
9
Remove ill fitting clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Check moving parts alignment on a regular basis.
9
Ensure workpiece is secure before operating the nibbler. Never hold a workpiece by hand. Use a vice or clamps.
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90psi.
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
9
Prolonged exposure to vibration from this nibbler poses a health risk. It is the employer’s/owner’s and operator’s responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
8
DO NOT
operate the nibbler near any flammable substance or on any container that once contained an flammable substance.
8
DO NOT
use the nibbler for a task it is not designed to perform.
8
DO NOT
operate nibbler if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT
carry the nibbler by the hose, or yank the hose from the air supply.
8
DO NOT
operate nibbler when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
carry the nibbler with your finger on the trigger.
8
DO NOT
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
WARNING!
The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
2. INTRODUCTION
n
W
ell balanced robust construction with fingertip operated throttle control. Suitable for cutting intricate shapes in steel up to 1.5mm thick. Punch
and die may be rotated through 360° to aid access and obtain maximum consumable life.
3. SPECIFICATION
Model No: ................................................................SA28.V2
Maximum Cutting Capacity: .............................
1.5mm (Steel)
Free Speed: ............................................................ 3000spm
Air Consumption: ........................................................... 4cfm
Operating Pressure: ...................................................... 90psi
Inlet Size: ..................................................................
1/4”BSP
Noise Power/Pressure: ........................................
99/88dB(A)
Vibration/Uncertainty: ......................................
7.75 / 1.5 m/s²
Consumable Parts:
Replacement Punch & Die Set: ..........................SA28PDKV2
4. PREPARATION
4.1.
Air Supply
4.1.1.
Remove protective plug from air inlet and connect to the air supply as described below.
4.1.2.
You will require an air pressure of 90psi, and an air flow according to the specification above.
WARNING!
Ensure the air supply is clean and does not exceed 90psi while operating the nibbler.
Too high an air pressure and unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/
or personal injury.
Refer to
instruction
manual
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Original Language Version
© Jack Sealey Limited
S
A28.V2 | Issue:4 (3) 01/04/20
