instructions for
air ratchet wrenches 3/8” & 1/2”sq. drive
model no:
sa20/s.v3 & sa21/s.v3
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFetY
warninG!
ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
warninG!
disconnect from air supply before changing accessories or servicing.
9
maintain the wrench in good condition and replace any damaged or worn parts. use genuine parts only. unauthorised parts may
be dangerous and will invalidate the warranty.
warninG!
check correct air pressure is maintained and not exceeded. We recommend 90psi.
9
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are
secure.
9
Only use impact sockets that are specifically designed for use with an air ratchet/impact wrench.
9
Wear approved safety eye/face shield, ear defenders, and hand protection.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and non essential persons away from the working area.
8
dO nOt
use the wrench for a task it is not designed to perform.
warninG! dO nOt
use wrench if damaged or thought to be faulty. (contact sealey stockist).
8
dO nOt
use wrench unless you have been instructed in its use by a qualified person.
8
dO nOt
carry the wrench by the air hose, or yank the hose from the air supply.
8
dO nOt
drop, throw or abuse the wrench as it is a precision tool.
8
dO nOt
operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
dO nOt
carry wrench with your hand on the power trigger in order to avoid unintentional starting.
8
dO nOt
direct air from the air hose at yourself or others.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
warninG!
the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. it must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2.
i
intrOductiOn
the air powered ratchet wrench has a hardened steel anvil and twist-to-reverse mechanism. With trigger operated power control the
wrench is suitable for use in the engine bay where there is limited space for hand operated rachets.
3.
i
speciFicatiOn
m
odel No:.........................SA20/S
.............................
SA21/S
d
rive size: ........................3/8” Sq
..............................
1/2” Sq
m
ax Torque.......................45ft/lb(61Nm)
..........
45lb.ft(61Nm)
free speed.......................150rpm .............................150rpm
Air consumption................5cfm ..................................... 5cfm
operating Pressure...........90psi ................................... 90psi
i
nlet Size...........................1/4”BSP
...........................
1/4”BSP
l
ength...............................265mm
.............................
265mm
Weight...............................1.2kg ................................... 1.2kg
n
oise Power/Pressure......106/95dB(A)
.............
106/95dB(A)
V
ibration/Uncertainty.........2.9/1.45m/s
2
.............
2.9/1.45m/s
2
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear protective
gloves
Wear eye
protection
Wear face
mask
Wear ear
protection
s
A20/S.V3, SA21/S.V3 Issue 1 09/02/18
