Sealey SA16, Instructions

Page: 1 / 2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p
WARNING! Ensure that Health & Safety, local authority, and general workshop practice regulations are
adhered to when using this equipment.
p
WARNING! Only persons holding a grinding wheel certificate are authorised to change grinding discs.
p
WARNING! Disconnect from air supply before changing accessories or servicing.
3
Maintain the grinder in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will
invalidate the warranty.
3
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
3
Before each use check abrasive disc for condition. If worn or damaged replace immediately.
3
Ensure that the speed rating (rpm) of the disc is the same as, or greater than, the speed rating of the grinder.
3
Ensure that there are no flammable or combustible materials near the work area.
p
WARNING! Always wear approved eye (or face) and hand protection when operating the grinder.
3
Use face, dust, or respiratory protection in accordance with COSHH regulations.
3
Depending on the task, grinder noise level may exceed 86dB in which case wear safety ear defenders.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the work area.
3
Check moving parts alignment on a regular basis.
3
Ensure that the workpiece is secure before operating the grinder. Never hold a workpiece by hand.
3
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
3
Avoid unintentional starting.
p
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this grinder poses a health risk. It is the owner’s responsibility to correctly
assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT use the grinder for a task it is not designed to perform.
7
DO NOT operate grinder if any parts are damaged or missing as this may cause failure and/or personal injury.
s DANGER! Use of damaged discs may cause damage and/or personal injury.
Grinding discs used in association with this machine shall be of an adequate speed rating and
suitable for the job in hand. The discs shall be made in accordance with British Standard BS ISO 525.
Only persons holding a grinding wheel certificate are authorised to change grinding discs.
p
WARNING! DO NOT grind any materials containing asbestos.
7
DO NOT carry the grinder by the hose, or yank the hose from the air supply.
7
DO NOT force, or apply heavy pressure to, the grinder, let the tool do the work.
7
DO NOT place air line attachments close to your face and do not point them at other people or animals.
7
DO NOT operate grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT use the grinder where there are flammable liquids, solids or gases, such as paint solvents and
including waste wiping or cleaning rags etc.
7
DO NOT carry the grinder with your finger on the power lever.
7
DO NOT direct air from the air line at yourself or others.
3
When not in use disconnect from air supply and store in a safe, dry, childproof location.
SA16 - 2 - 250205
INSTRUCTIONS FOR:
180mm ANGLE GRINDER
Model:
SA16
01284 757500
E-mail: sales@sealey.co.uk
Web address: www.sealey.co.uk
01284 703534
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
Sole UK Distributor, Sealey Group , Bury St. Edmunds, Suffolk.
ITEM PART NO. DESCRIPTION
01. SA16/01 HANDLE
02. SA16/02 BUSH
03. SA16/03 THROTTLE
04. SA16/04 CAP SCREW
05. SA16/05 CLAMP NUT
06. SA16/06 GOVERNOR CASE
07. SA16/07 VALVE
08. SA16/08 WASHER
09. SA16/09 PENDULUM
10. SA16/10 GOVERNOR SPRING
11. SA16/11 GOVERNOR BODY
12. SA16/12 GASKET RING
13. SA16/13 CASING
14. SA16/14 PLATE
15. SA16/15 CYLINDER
16. SA16/16 ROTOR
17. SA16/17 ROTOR VANE
18. SA16/18 FRONT END PLATE
ITEM PART NO. DESCRIPTION
19. SA16/19 SPRING PIN
20. SA16/20 BEVEL PINION
21. SA16/21 BEVEL GEAR
22. SA16/22 SHAFT
23. SA16/23 KEY (3X3X10)
24. SA16/24 KEY (5X5X10)
25. SA16/25 KEY (4X4X15)
26. SA16/26 SCREW
27. SA16/27 DISC
28. SA16/28 DISC
29. SA16/29 GRIP HANDLE
30. SA16/30 DISC COVER
31. SA16/31 INLET BUSHING
33. SA16/33 OIL PLUG SCREW
41. SA16/41 USE SA15/51 PIN
42. SA16/42 THROTTLE LEVER
43. SA16/43 O-RING
44. SA16/44 CONICAL SPRING
ITEM PART NO. DESCRIPTION
45. SA16/45 GASKET RING
46. SA16/46 PLUG
48. SA16/48 STOP RING
49. SA16/49 SPRING PIN
50. SA16/50 HEX CAP BOLT
51. SA16/51 SPRING WASHER
52. SA16/52 HEX HEAD BOLT
53. SA16/53 SPRING WASHER
54. SA16/54 HEX NUT
55. SA16/55 WASHER
56. SA16/56 SCREW
57. SA16/57 SPANNER
58. SA16/58 HEX KEY
59. BEARING B/608Z
60. BEARING B/6200Z
61. BEARING B/6201Z
62. BEARING B/6201Z
63. BEARING B/6303
PARTS LIST FOR:
180mm ANGLE GRINDER
Model:
SA16
Issue: 1
Date Issued: 150104
DANGER OF FIRE/EXPLOSION HAZARD
o
o
WARNING! The grinding process can produce streams of sparks (especially when grinding metal) which are a potential source of ignition.
7
7
DO NOT use the grinder where there are flammable liquids, solids or gases.
7
7
DO NOT allow grinder sparks to make contact with the operators clothing or any other fabric such as cleaning rags. Fabrics
contaminated with inflammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
3
3
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant, in
preference to man-made fibres.
For Jack Sealey Ltd. Sole importer
into the UK of Sealey Power Tools.
180mm Angle Grinder
Model: SA16
98/37/EC Machinery Directive
93/68/EEC Marking Directive
25th February 2005
Declaration of Conformity
We, the sole importer into the UK, declare that the product listed here is
in conformity with the following standards and directives. The construction file for this product is held by the Manufacturer
and may be inspected, by a national authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman