![background image](http://html.mh-extra.com/html/sealey/re225-v3/re225-v3_instructions_1224015001.webp)
instructions for
coil spring compressor kit 1800kg
model no:
re225.V3
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. sAFetY
▲
DAnger
! stop compressing the spring before the coil windings touch. exercise particular caution when using an air impact
wrench. failure to observe this rule may damage the safety pin.
WArning!
ensure Health & safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
9
Before each use, check the unit for full functional capability. if the functional capability is not ensured or if damage is detected, the unit
should not be used and you should contact your supplier immediately.
WArning!
Wear approved safety eye protection (standard spectacles are not adequate) and protective gloves.
WArning!
Do not
compress the spring to an extent where the jaws touch.
8
Do not
use the compressor for other purposes than it was designed for and
Do not
oVerloAD
the compressor.
8
Do not
operate spring compressor if parts are damaged or missing as this may cause failure and/or personal injury.
9
maintain the spring compressor in good condition. replacement or repair of damaged parts must be carried out by competent
personnel. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
8
Do not
force the spring compressor to achieve a task it was not designed to perform.
8
Do not
allow untrained persons to use the spring compressor.
9
familiarise yourself with the applications, limitations and potential hazards of the spring compressor.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep hands and body clear of the spring when operating the spring compressor.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothes. Remove ties, watches, rings, other loose jewellery. Contain and/or tie back long hair.
9
for indoor use and at room temperature only.
9
When not in use clean and store the spring compressor in a safe, dry, childproof location.
see Also oPerAtionAl sAfetY section 4.1
2. introDuction
High quality, european made, 1800kg coil spring compressor kit. supplied with two pairs of drop forged safety yokes, with polyurethane inserts
for improved grip. Yokes are carefully shaped to prevent coil spring from bowing. features safety restraint wire as a precaution, in the unlikely
event of a spring slipping. suitable for use with air impact wrench.
3. speciFicAtion
model no: ...............................................................re225.V3
Y
oke specification:
size (spring diameter)
small: ........................................................
Ø80 - 120mm (x2)
large: ........................................................
Ø80 - 195mm (x2)
drive: .................................................................... 27mm hex
maximum jaw opening:............................................... 335mm
capacity: .................................................................... 1800kg
4. operAtion
4.1.
operAtionAl sAFetY
4.1.1.
When compressing the spring, neither the spring windings nor the jaws should come in contact with each other, see figure B.
4.1.2.
the centre line of the spring must always be parallel to the compressing device, especially for conical springs.
4.1.3.
use only suitable jaws for the springs. the spring must rest securely within the outer rib and the safety ridges. take care that the
spring cannot slide out of the jaws.
4.1.4.
When using air wrench, torque limitation is 120 nm.
4.1.5.
Pay attention to compressed spring. never drop or impact compressed spring, which can cause serious injury.
4.1.6.
use only for coil springs mentioned in this user instruction.
4.1.7.
The bolts of the jaws must always be firmly tightened with 60 Nm torque.
8
Do not
make any construction changes to the unit, especially to the safety pin.
8
Do not
leave compressed spring unattended.
re225.V3 | issue:2 (2) 12/12/17
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear eye
protection
Wear
protective
gloves