background image

1.1. 

ELECTRICAL SAFETY

  

WARNING!

 It is the responsibility of the owner and the operator to read, understand and comply with the following:

 

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and    

 

any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate  

 

safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend  

 

that a Residual Current Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a  

 

supply which is not protected by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by  

 

contacting your Sealey dealer. 

 

You must

 also read and understand the following instructions concerning electrical safety.

1.1.1. The 

Electricity at Work Act 1989 

requires that all portable electrical appliances, if used on

 

business premises, are tested by a qualified electrician, using a Portable Appliance Tester (PAT), 

 

at least once a year.

1.1.2. The 

Health & Safety at Work Act 1974 

makes owners of electrical appliances responsible for the

 

safe condition of those appliances and the safety of the appliance operators. 

If in any doubt 

 

about electrical safety, contact a qualified electrician.

1.1.3.  Ensure that the insulation on all cables and on the appliance is safe before connecting it to the

 

power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.

1.1.4.  Ensure that cables are always protected against short circuit and overload.

1.1.5.  Regularly inspect power supply cables and plugs for wear or damage and check all connections to 

 

ensure that none is loose.

1.1.6. 

Important:

 Ensure that the voltage marked on the appliance matches the power supply to be used

 

and that the plug is fitted with the correct fuse - see fuse rating at right. 

1.1.7. 

DO NOT

 pull or carry the appliance by the power cable.

1.1.8. 

DO NOT 

pull the plug from the socket by the cable.

1.1.9. 

DO NOT

 use worn or damaged cables, plugs or connectors. Immediately have any faulty item

 

repaired or replaced by a qualified electrician. When a BS 1363/A UK 3   pin plug is damaged, cut the cable just above the plug and    

 

dispose of the plug safely. 

 

Fit a new plug according to the following instructions (UK only).

 

a)  Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 b) 

Connect the BROWN live wire to the live terminal ‘L’.

 

c)  Connect the BLUE neutral wire to the neutral terminal ‘N’.

 

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer 

 

  insulation extends beyond the cable restraint and that the restraint is tight.

 

Double insulated products, which are always marked with this symbol      , are fitted with live (brown) and neutral (blue) wires only. To  

 

rewire, connect the wires as indicated above - 

DO NOT

 connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure  

 

that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with  

 

your electrician.

1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance    

 

plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the   

 

capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of  

 

2.5mm² section cable. 

1.2  

GENERAL SAFETY

 

WARNING!

 

Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this    

 

 equipment.

  Familiarise yourself with the application, limitations and potential hazards of the staple gun.

  Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

  Locate staple gun in a suitable working area, keep area clean and tidy and free from unrelated materials.

 

Keep the work area clean, uncluttered and ensure there is adequate lighting.

  Keep the staple gun clean for best and safest performance.

  Ensure there are no flammable or combustible materials near the work area.

 

Wear approved safety eye protection (standard spectacles are not adequate).

 

Wear heat resistant gloves and appropriate protective clothing.

RECOMMENDED

 FUSE RATING: 13AMP

InSTRUCTIonS FoR: 

PLASTIC REPAIR HOT STAPLE GUN

moDEL no:

 RE023

 1.  SAFETY

Original Language Version

 © Jack Sealey Limited

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE 

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

Wear eye 

Protection

 

Wear 

Respiratory

Protection

Wear Heat 

Resistant Gloves

Hot Surfaces

RE023    Issue: 1 - 15/05/14

Reviews:

Related manuals for RE023